¡A uniform circular ring has a mass of m= 20 kg and a diameter of p = 300 mm. It is supported by three wires each of length /= 250 mm. If a = 120°, B = 150⁰, and y = 90°, determine the tension in each wire. Hint: use y as a convenient way to align your xyz-coordinate axes, then solve it in a similar fashion to 3D Particle Statics Practice Problem 1.

¡A uniform circular ring has a mass of m= 20 kg and a diameter of p = 300 mm. It is supported by three wires each of length /= 250 mm. If a = 120°, B = 150⁰, and y = 90°, determine the tension in each wire. Hint: use y as a convenient way to align your xyz-coordinate axes, then solve it in a similar fashion to 3D Particle Statics Practice Problem 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Chapter 8, Question 14: Something is wrong with the orientation of the ropes shown in Figure Q8.14. Use the first condition of equilibrium for the hanging pulley to help explain this error, and then redraw the sketch as you would expect to see it.
2. A kilogram mass is attached to the end of the spring with spring constant 2 N/m. Find the equation of motion if the mass is initially released (set in motion) from rest from a point 1 meter above equilibrium position. (Use the convention that displacements measured below the equilibrium position are positive.) (a) Write the initial-value problem which describes the position of the mass. (b) Find the solution to your initial-value problem from part (a). (c) Graph the solution found in (b) on (0
After the web meeting, submit this document on Canvas Undel ne Meeting Assignment. This is an individual submission. TAE %3D Follow the steps below to express the force F, as a vector using the format: F, = F 1. Write the position vector: TAE = 4 ft 4 ft F = 300 lb 6 ft 6 ft 2. Find the magnitude of the position vector: 6 ft TAE = F = 400 lb 3. Find the unit vector by dividing the position vector by its own magnitude: NAE = 4. Write the force vector: F1 =FinAE =
HCM-6 At the design speed Vo Dan's car can go around a banked curve of radius 150M and banking angle of 10.0° without any friction force. The car is shown as viewed from behind in the figure below. R=150m 10.0° a) Use the figure above to draw the free body diagram for the car. Also show on the FBD the direction of the car's acceleration and show coordinate axis directions. b) Write down newtons's second law in component form for the car. Use NO numbers for this part. c) Use your equations from step b) to find the design speed Vo.
The mechanism shown in the figure controls the lifter. Calculate the reactions on CDE as the weight supported by the platform is W W(N)= 2800, L1(m)=0.6, L2(m)=0.6 , L3(m)=0.2 1) For three dimensional problems, please use vector notation.2) State what all the transactions you have done. All intermediate actions you have to doshow clearly.3) Please write the units next to the values you find.4) In the related questions, please draw the free body diagram.
You have a lever, 2m on each side, and four masses: 5kg, 10kg, 15kg and 20kg. You will place the blocks at different positions on the lever such that the two sides balance. Place each block a unique distance from the fulcrum. Use a torque balance to prove the system will not move.
6. Two close-coiled helical springs are arranged, parallel (one inside the other) about the same longitudinal axis. Both springs have the same number of coils and same overall length, but the mean coil diameter of the outer spring, which is made of steel wire, is twice that of the inner spring, which is made of bronze wire. The springs are designed to act together when a tensile force is applied, so that both suffer the same change in length and each carries half the force. Determine the ratio of the wire diameters, and the retio of the stresses produced in the wires, if Esteel = 2 x Ebronze
igure 2. Assume that the rod is massless, perfectly rigid, and pivoted at point P. When the rod is perfectly horizontal, the angle 0 = 0, the displacement y 0, and the springs are in neither tension nor compression. Gravity acts on the system (e.g. on mass M). We assume that y is a small displacement. A mass M is attached at the end of the rod. DE only 225 Your tasks: X k 0 3k a F a M y A Derive an equation of motion for the system in terms of the angular displacement 0, and its derivatives (you should not have y or its derivatives in this equation.) B Derive an equation of motion for the system in terms of the displacement y, and its derivatives (you should not have or its derivatives in this equation. C Assuming there is no external actuator force F acting on the system, write down the total energy H of the system in terms of 0,0 and element constants. Derive an expression for the time derivative H of the total energy. D Transform the equation from part B, which is in y, to another…
Using either Graphical Analysis or graph paper, plot a graph of pendulum period T vs. lengthl. Scale each axis from the origin (0,0). Does the period appear to depend on length?
Answered: T Blackboard @ Texas X Bb MasteringEngineering - Spring 2 × E MasteringEngineering Mastering x > (195) Find the resultant force acti X O (195) Morgan Wallen - Cover i session.masteringengineering.com/myct/itemView?assignmentProblemID=12360390 ABP G I Review Suppose that h = 4 m. (Figure 1) Part C Determine the coordinate direction angle B of the resultant force of the two forces acting on the sign at point A. Express your answer using three significant figures. B = 90 Submit Previous Answers v Correct Part D Figure 1 of 1 Determine the coordinate direction angle y of the resultant force of the two forces acting on the sign at point A. 2 m Express your answer using three significant figures. E 2 m B Hν ΑΣφ ? vec F = 350 N Fc= 400 NA F = 400 N 2 m Submit Request Answer 3 m Provide Feedback Next > 11:50 PM O Type here to search 2/7/2021
0.5 m, k = 500 N/m, and k = 40 N.m/rad, In the system shown, m = 10 kg, r = 0.3 m, Ko where ko is the radius of gyration of the pulley about point 0. There is no slippage between the cord and the pulley. Replace the system with an equivalent { a) torsional spring and mass moment of inertia at point 0, and b) translational mass and spring at point A. т, Ко kt А k m ww
Sketch a free body diagram of your iOlab as you hold in it very steady by the eyebolt attached to the force sensor. What is the net force (the vector sum of forces) on the iOLab? Is the iOLab device accelerating? Explain your answer.