A trapezoidal channel with a bottom width of 3.0 m andsides with a slope of 2:1 (horizontal: vertical) is linedwith fine gravel (n = 0.020) and is to carry 10 m3/s.The channel bed slope is 0.001.a) For the given channel, express the hydraulic radius,Rh, and hydraulic depth, y, in terms of the depth of flowsection, y.b) Using an ultrasonic flow meter, the average velocityat a certain cross-section of the channel is measuredand is equal to 0.75 m/s. Find the Froude number atthis portion of the channel.c) Calculate the normal depth, yn.d) Calculate the critical depth, yc.2Y3m124

Name: A trapezoidal channel with a bottom width of 3.0 m andsides with a sl
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A trapezoidal channel with a bottom width of 3.0 m andsides with a slope of 2:1 (horizontal: vertical) is linedwith fine gravel (n = 0.020) and is to carry 10 m3/s.The channel bed slope is 0.001.a) For the given channel, express the hydraulic radius

INTRODUCTION: The movement of liquid through a channel with a free surface is referred to as open…

Engineering

Mechanical Engineering

A trapezoidal channel with a bottom width of 3.0 m and sides with a slope of 2:1 (horizontal: vertical) is lined with fine gravel (n = 0.020) and is to carry 10 m3/s. The channel bed slope is 0.001. a) For the given channel, express the hydraulic radius, Rh, and hydraulic depth, y₁ in terms of the depth of flow section, y. b) Using an ultrasonic flow meter, the average velocity at a certain cross-section of the channel is measured and is equal to 0.75 m/s. Find the Froude number at this portion of the channel. c) Calculate the normal depth, yn. d) Calculate the critical depth, yc.

A trapezoidal channel with a bottom width of 3.0 m and sides with a slope of 2:1 (horizontal: vertical) is lined with fine gravel (n = 0.020) and is to carry 10 m3/s. The channel bed slope is 0.001. a) For the given channel, express the hydraulic radius, Rh, and hydraulic depth, y₁ in terms of the depth of flow section, y. b) Using an ultrasonic flow meter, the average velocity at a certain cross-section of the channel is measured and is equal to 0.75 m/s. Find the Froude number at this portion of the channel. c) Calculate the normal depth, yn. d) Calculate the critical depth, yc.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Most efficient weir of weirs used in laboratory.
Q.10. The flow net below represents air flowing over a small hill. 1.8m .d 1.5m 1.2m 0.9m • a 2m At the inlet, the streamlines are evenly spaced 2 m apart, and the air flow is a uniform 3 m/s. a. Taking the ground to be = 0 m²/s, what are the values of the streamlines A-C? b. Find the air flow speed, and the corresponding gauge pressure, at each of the points a-d at the crest of the hill. c. The stream and potential lines have been drawn to be approximately square. As- suming this to be the case, what is the value of the potential drop Aø1 and A¢2.
8. The displacement y(t) of a spring-mass system shown is given by ÿ(t) + 25y(t) = f(t). k = 25 N/m m = 1 kg y(t) f(t) a) Find the transient solution, ytrans (t). b) Find the steady state solution of the displacement yss if f (t) = 10 N.
b) Given the below conditions are given for a partially circular channel shown in Figure2.▪ Flow = uniform▪ Density, ρ = 998.0 kg/m3▪ Dynamic viscosity, μ = 1.002 x 10^-3 kg/m∙sCalculate the hydraulic radius, Reynolds number, and the type of flow.
HYDRAULICS/FLUID MECHANICS. RATE WILL BE GIVEN. 3 DECIMAL PLACES
Fluid Mechanics: Open Channel Flow
1. In a steady spatially varied flow in a prismatic open channel, the (a) depth does not change along the channel length (b) discharge is constant along its length (c) discharge varies along the length of channel (d) discharge varies with respect to time.
Please answer Fluid Mechanics Hw problem #8
Can i get the answer as an image i cant see the whole write up Tried using my laptop same issue
Problem 5: Pipe Flow A 10,000 ft P BC 20,000 ft D This semester we worked through several versions of the pipe flow problem sketched above, in which a 3.0 ft diameter pipe is used to convey water from reservoir A (surface elevation 80 ft) to reservoir D (surface elevation 90 ft). In week 14, we considered a specific example with a cast iron pipe (A = 0.00085 ft), flow rate of Q=40 ft³/s, and average velocity of V = 5.66 ft/s. For these conditions, the friction factor was λ = 0.015 and the pump added 86 ft of head. Assume the water temperature is always 60°F. Part A Assuming the pump is 75% efficient and electricity costs 10e/kW.hr, how much will it cost to run this pump for a year? Hint, 1 kW hr = (1000 watts) (1 hr) = (1000 J/s)(3600 s) = 3.6x106 J. Part B Now let us assume we need to double the discharge to Q = 80 ft³/s, but unlike the example in week 13, we are not going to make the false assumption that the friction factor λ is constant. You may, however, assume that the roughness…
No. Date. Determination of Discharge Thru a Siphon Vol . Q=AV t J P1 P2 +21=(√2) ² 29 + 1² + Z2 r Y trial #2 trial #3 t = 75 t= 5s Y = 340ml V: 250mL the table below I show calculation please) 1 Theoretical Actual + Discharge (s) + Discharge (LIS) Formula: Q= (V1)2 29 h = 63.5cm trial #1 t= 10s V = 490 mL complete trial + time(s) Volume (ml) 1 %0 + Difference
1. An actual discharge from a reservoir takes place over a rectangular weir where the flow characteristic is Q= 1.77 BH 3/2 m³/s (a) Find the length of weir (b) The ratio of actual discharge to theoretical discharge * Required to discharge 9 m³/s, if head must not exceed 0.6m