A torque of 10 kN - m is supplied to the steel (G = 80 GPa) factory drive shaft of Fig. P7-8 by a belt that drives pulley A. A torque of 6 kN - m is taken off by pulley B and the remainder by pulley C. Shafts AB and AC are 2.25 m and 1.60 m long, respectively. If the diameter of shaft AB is 80 mm and the diameter of shaft AC is 65 mm, determine (a) The maximum shearing stress in each of the shafts. (b) The angle of twist of pulley B with respect to pulley A. (c) The angle of twist of pulley C with respect to pulley B. Figure P7-8

A torque of 10 kN - m is supplied to the steel (G = 80 GPa) factory drive shaft of Fig. P7-8 by a belt that drives pulley A. A torque of 6 kN - m is taken off by pulley B and the remainder by pulley C. Shafts AB and AC are 2.25 m and 1.60 m long, respectively. If the diameter of shaft AB is 80 mm and the diameter of shaft AC is 65 mm, determine (a) The maximum shearing stress in each of the shafts. (b) The angle of twist of pulley B with respect to pulley A. (c) The angle of twist of pulley C with respect to pulley B. Figure P7-8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the…

Q: (A,) See the figure below. There are two torques applied at B and D. Segment CD is a tube, while AB…

A: In the given problem, the dimensions and Modulus of rigidity have been converted to feet. Radius,…

Q: An open coiled heilcal spring made of 6 mm diam- eter steel wire and 60 mm mean coil diameter, with…

A: We know that an axial torque T is applied to an open coiled helical spring formed of 6 mm diameter…

Q: Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an…

Q: maximum shear stress that is generated through the shaft.

Q: In the figure above, torques TI, T2 and T3 are applied, respectively, to discs A, B and C on the…

Q: A two-segment shaft is used to transmit power at constant speed through the pulleys shown in the…

Q: Please give a detailed explanation with a free body-diagram.

A: To provide a detailed explanation along with a free body diagram (FBD) for determining the reaction…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Bronze: Length, Lbronze= 2 mDiameter, Dbronze= 25 mm= 25×10-3 mGbronze= 35 GPa= 35×109 Pa Aluminum:…

Q: A vertical shaft DA is attached vertically to a fixed base at A and is subjected to the torques as…

Q: Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show…

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be…

A: Here is the solution for the above question.

Q: In the figure, shaft AB transmits power to shaft CD through a set of bevel gears contacting at point…

Q: Determine the internal torques, T₁ and T2, in segments (1) and (2), respectively. Use the internal…

Q: 11 A rectangular bar section of aluminium alloy has outside dimensions 100 mm x 50 mm, as shown in…

A: As illustrated in the image, a rectangular bar section of aluminium alloy has outer dimensions of…

Q: Consider the compound shaft KC which is compose of a 1200mm long solid rod fitted snuggly into an…

Q: An oversized yo-yo is made from two identical solid disks each of mass M = 1.90 kgand radius R =…

Q: Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure ,…

A: The angle of Twist: The angle at which the fixed end of shat rotates with respect to its free end is…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

Q: A torsional bar is subjected to two external torques (10Nm and 5Nm) and a distributed torque…

A: according to the details given above

Q: Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure ,…

A: Write the torque developed on the taper shaft. T=20 kN·m=20 kN·m×1000 N·m1 kN·m=20×103 N·m Write…

Q: A shaft given in the figure has four masses of 200 kg, 300 kg, 400 kg and 200 kg, respectively. and…

A: Consider the balancing masses in plane L as and in plane R as .Represent the position of planes and…

Q: A belt driven pulley, transmitting torque , weighs 1.8 kN. It is mounted between two bearings 3 m…

Q: A two-segment shaft is used to transmit power at constant speed through the pulleys shown in the…

Q: The two bearings (B1) and (B2) are used to support a shaft as shown in the figure Using the data…

Q: 900 N-m A 1100 N-m B. 2 m 800 N-m 3 m

A: A rotating member usually is a circular cross-section used to transmit rotational power from one…

Q: 2. A shaft is designed to carry torque as shown below. The shaft consists of a steel rod which is…

Q: as a diameter ofd₁= 57 mm and length ofL₁= 0.75 m; segment 2 has a diameterd₂= 44 mm and lengthL₂=…

A: Twisting Moment:- A couple of forces produce a moment in a material that is known as a twisting…

Q: A steel stepped shaft ABCD fixed at A is subjected to three torques at points B, C and D, with…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: 40 Steel d = 30 mm A G= 83 GPa 1.2 m

A: Calculated resisting torque at support at A and B .

Q: Prob. 4.5-9. Use the following data with Fig. P4.5-9: G = 11 × 10° psi, L1 = 10 in., L2 = 15 in., L3…

Q: A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional…

A: Transient response: the response of the system due to free vibration is called the transient…

Q: Shaft AB is 3 meter long and is free at the left end and fixed torsionally at the right end. It is…

A: Given:

Q: A counterweight of mass m = 5.00 kg is attached to a light cord that is wound around a pulley as…

Q: Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each…

Q: A steel shaft (G = 80 GPa) with an external drive of 30mm must transmit a torque of 2700 N-m. The…

Q: T3 T2 18215112 T1 D b180100003-1821511 b180108003 1828151128 `dcp dBcC B. b18010000318151126…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A torque of 10 kN - m is supplied to the steel (G = 80 GPa) factory drive shaft of Fig. P7-8 by a belt that drives pulley A. A
torque of 6 kN - m is taken off by pulley B and the remainder by pulley C. Shafts AB and Ac are 2.25 m and 1.60 m long,
respectively. If the diameter of shaft AB is 80 mm and the diameter of shaft ACis 65 mm, determine
(a) The maximum shearing stress in each of the shafts.
(b) The angle of twist of pulley B with respect to pulley A.
(c) The angle of twist of pulley Cwith respect to pulley 8.
Figure P7-8
B
-Bearing

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given Data

VIEW

Resisting torque

VIEW

The maximum shearing stress in each of the shafts.

VIEW

The angle of twist of pulley B with respect to pulley A

VIEW

The angle of twist of pulley C with respect to pulley B

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is transmitted via the drive shaft, ABC. The section AB is a solid circular shaft 0.7 m long and the section BC is a hollow circular shaft 1.0 m long with 110 mm outer diameter and 55 mm inner diameter. Both shafts are made from a metal alloy (Shear Modulus G = 95 GPa). 0.7 m 1.0 m A в 2400 hp @ 2000 rpm Figure 3 a) If the drive shaft rotates at 2000 rpm and the power transmitted along the shaft is 2400 hp (1 hp = 745.7 W), calculate the torque developed in the drive shaft.
A rope pulley is supported by two deep groove ball bearings as shown in the figure. A force of FR = 7 kN acts on the pulley in the radial direction. If Fa = 0.5kN, axial force acts. The rolling diameter of the pulley is d = 300 mm and the rope speed is v = 4 m / s. The nominal life of the bearings is required as Lh = 27000 h. Since the diameter of the shaft where the bearing is bearing is 45 mm, choose the appropriate bearing. V = N.D.n
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 50; TB = 70; TC = 30; TD = 10. The directions of the applied torques are indicated in the figure. The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Use the same rule of signs as in the lecture. Determine (b) the maximum shear stress magnitude (ksi) in the shaft. (c) the rotation angle, in degrees, of pulley D with respect to pulley B. Note: Follow the rule of signs with FBD in each sections. Show complete step by step solution and proper FBD. Solid shaft: J = (₶/32 )( D4) Hollow: J = (₶/32)(D4 - d4)
Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure , Determine the angle of rotation at the free end. D2 D1 T (kN-m) Given: L(m) T(KN-m) D1 (mm) 02 (mm) G (GPa) 28 60 140 120
In the figure below, a motor with power 150kw and speed of 2500 rpm is connected to shaft 1(by coupling) in a clockwise direction. Shaft 2 is connected to shaft 1 by gears 1 and 2. If 30% of the power is consumed by the gear3 and 9% by the pulley and 61% by the sprocket, draw torque diagrams for both shafts. • Lengths: AB=90mm/BC=GH=50mm/CD3HI=60mm/DE=IJ=80mm 13 Gear3 E Gear2 14 15 16 Motor shafth 2. 17 Bearing Shaft1 Gear1 sprocket
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.
Please answer in proper units
A solid shaft made from AISI 1040 cold-drawn steel is used to carry two V-belt, as shown in the Fig. 3. Pulley A receives power from a motor through a belt, with the belt tensions shown in Fig. 3. The power is transmitted through the shaft and delivered to the belt through pulley B. Assume the belt tension on the loose side is 10 percent of the tension on the tight side.
Two solid circular shafts are connected through a flange bolt coupling consisting of 3 circular bolt rows. The free ends of the shafts are to be subjected by equal torque. Solid Shafts Diameter (mm) Length (m) Shear Modulus (GPa) Shaft A Shaft B 65 66 3 3.8 81 84.6 Flange-bolt coupling Bolt Circle Diameter (mm) Bolt Alowable Shear Stress (MPa) Bolt Diameter Shear Modulus Number of Bolt Row (mm) (GPa) Bolts 1 95 14 77 35 4 2 116 17 97 42 10 3 135 13 93 49 14 A Calculate the torque capacity of the flange-bolt coupling (kN-m). B. Calculate the stresses in both shaft if the torque capacity is applied at both ends (MPa). C. Calculate the total angle of twist (in degrees).
9)