A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be driven by vee belts through a pulley. The combined tensions of the belt apply and the weight of the pulley assembly applies a force of 5.4kN and 900N respectively. The shaft has a diameter of 32mm. Bearing A at the top supports the shaft radially whereas bearing B at the bottom supports the shaft axially and radially. Two deep groove ball bearings have been selected for this application. The models of the bearings are SKF 6305 and SKF 6205 for bearing A and B respectively. a)      What are the forces at bearing A and B?   b) Paste a screenshot of the graph showing the distribution of the forces in the shaft.   c) From the report, find the static load capacity for: Bearing A Bearing B

Q: 13. For the same Figure in Problem 11, the reaction at the fixed support B is- a. 645 N-m (CW) b.…

A: Torque given are 800 Nm and 500 Nm. Diameter of the shaft, d= 20 mm= 0.02 m

Q: The figure 1 shows a pulley assembly that consists of a shaft supported by two bearings and driven…

A:

Q: Please give a detailed explanation with a free body-diagram.

A: To provide a detailed explanation along with a free body diagram (FBD) for determining the reaction…

Q: A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mm has been designed to…

A: Given: Pressure = 200 Mpa To find: Radial and circumferential stress using Lame's equation Sketch…

Q: shows two pulleys are fixed to the shaft and supported by the roller bearing at points A and B.…

A: Given Data:

Q: The answers I got for A and B are correct. The following is the remaining answers I got which are…

A: Step 1:Based on the information provided in the image, the resultant bending moment acting on the…

Q: (a) List down 2 assumptions needed in designing the shaft in Fig. 3. Design the minimum allowable…

A: DefinitionBending Moment:If an object undergoes a bend about its certain axis due to some tendency…

Q: Ball bearings are rated by a manufacturer for a life. of 106 revolutions. The catalogue rating of a…

A: Given Data:-Catalog rating, F1=16 kNLife of beating, L1=106 revolutions

Q: Perform free body diagram analysis to get reaction force at bearings

A: Consider the shaft lies in xy - plane as shown below and draw free body diagram.Here  indicates…

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: The diameter of the shaft DF is The power at F is The power at A is The power at B is The power at C…

Q: The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a…

A:

Q: A 1500 kg load is lifted by a hoist using a Ø1.5 m drum. The drum is driven by an electric…

A:

Q: A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in…

A:

Q: Two parts of a machine, both made from steel, are held together by 7 equally-spaced M6 x 1.0 grade…

A: Given : Preload, F = 60 kN K = 0.18  M6 x 1 bolt D = 6 mm To find : Torque required

Q: The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a…

A:

Q: The 6.0-1b bar is pinned at its center O and connected to a torsional spring. The spring has a…

A: In this problem first the moment about O is taken and the acceleration is integrated to get the…

Q: 3. A flat annular steel flywheel of outer radius 0.5 m and inner radius 0.125 m with p = 7800…

A:

Q: An axle is composed of elements laid by S355 E-module 2.1x105 N/mm2, transverse contraction factor…

A: it appears to be a schematic of a shaft under bending load. Here's how to approach the problem:v)…

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm  D=41mmPCD=63mm

Q: Please answer: 3, 4, 5, 6, 8, 9, 10, 12  The only correct answers are 1 (0), 2 (0), 7 (point A).…

A:

Q: 2. A stationary shaft and pulley subjected to a 2000-lb static load. (1) Draw the FBD of the 1-in…

A: Given:The length of the shaft, The diameter of the shaft, The radius of the pulley, The static load…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.