A three-phase switched reluctance motor has Ns = 6 stator poles, Nr = 4 rotor poles and two coils per phase on opposite stator poles with Np = 50 turns each. A current of i = 10 A flows through the two coils in series. Assume that the unaligned inductance Lu = 0 H, and the aligned inductance La 0.011 H. Calculate the electromagnetic torque and angle of rotation at which the torque is essentially constant, if the current is constant. %3D

A three-phase switched reluctance motor has Ns = 6 stator poles, Nr = 4 rotor poles and two coils per phase on opposite stator poles with Np = 50 turns each. A current of i = 10 A flows through the two coils in series. Assume that the unaligned inductance Lu = 0 H, and the aligned inductance La 0.011 H. Calculate the electromagnetic torque and angle of rotation at which the torque is essentially constant, if the current is constant. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is ampere circuital law?
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
The contractor is controlled by?
4. Do some search about the functionality of Airport Metal Detectors. Explain your answer in a paragraph.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies