A three-phase delta-connected load, each phase of which has an inductive reactance of 40 Ω and a resistance of 25 Ω, is fed from the secondary of a three-phase star-connected transformer which has a phase voltage of 230 V. Draw the circuit diagram of the system and calculate: (a) the current in each phase of the load; (b) the p.d. across each phase of the load; (c) the current in the transformer secondary windings; the total active power taken from the supply and its power factor.

A three-phase delta-connected load, each phase of which has an inductive reactance of 40 Ω and a resistance of 25 Ω, is fed from the secondary of a three-phase star-connected transformer which has a phase voltage of 230 V. Draw the circuit diagram of the system and calculate: (a) the current in each phase of the load; (b) the p.d. across each phase of the load; (c) the current in the transformer secondary windings; the total active power taken from the supply and its power factor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

I need the answer quickly
8. The circuit below is similar to Problem 7 and operates at a frequency of 10 kHz. Circuit element Z can be either a capacitor or inductor. Assuming the transformer is ideal, determine the inductance or capacitance of Z and the turns ratio N that optimizes the power delivered to the load, RL , then calculate the power in R1. 1:N k 10490° R= 200 2 -j4 2 =
A 220V(rms), 50HZ sinusoidal source is connected to the primary side of an ideal transformer with 100 turns on the primary side and 300 turns on the secondary side. Primary line resistance is 22 and inductance is 10mH. Secondary line resistance is 92 and inductance is 100mH. There is a 1002 resistive load connected on the secondary side. Draw a well-labeled circuit diagram and determine: (i) Currents on both sides (ii) Load Voltage (iii) Complex power supplied by the source
generator (b) What is the average power dissipated in R? P=[ W Help Enter 500 v generator voltage -500 v AC Generator 0 Ideal Transformer R = 300 Rg8 time (a) The sinusoidal voltage output from the AC generator oscillates between 500 V and -500 V. The circuit for an ideal transformer is constructed with a generator, transformer and a 30 W resistor. The generator makes 6 loops with the transformer and the resistor makes 11 loops with the transformer (the figure does not show these loops accurately). What is the maximum voltage across the resistor R? V= V Help Enter
An inductive reactance of 6 ohm is connected in series with a parallel combination of a variable resistor R and a capacitive reactance of 15 ohm across 100V , 50 hz supply. a. Solve for the frequency so that the magnitude of the inductive reactance is 2 times the magnitude of capacitive reactance. b. Solve for the value of R so that the total current I will be maximum.
Please answer the questions on the figure!
Excercies: 1. Two transformers A and R to a load of (2+jh5) Their impedanas in secondary terms Coltjo.6)5r EA = 200 Lov output and Power factor of each transformer are Connected in parallel ZA = (o15t+j 0.8)2 and zR= Their noload termind nltages are and Es = 21010V Fnd the poer are %3D 11 2. Two trans formes A andB of ratings 500KVA and 25okVA supplying a load kVA of 750 at a8 Pf lagging. Their open circuit voltayes are 400V and 410V respecctively. Transformer A has 1% rsistance and 5/ reactance and transformer B hay s resistance and 4 reactance. Fnd (a) Cross-curnt in the seondaries load shared by each transforcmer. are on no-load,b) the 2.
You are working in an industrial plant. A three-phase transformer bank is connected wye–delta. The primary voltage is 12,470 V, and the secondary voltage is 480 V. The total capacity of the transformer bank is 450 kVA. One of the three transformers that form the three-phase bank develops a shorted primary winding and becomes unusable. A suggestion is made to reconnect the bank for operation as an open-delta. Can the two remaining transformers be connected open-delta? Explain your answer as to why they can or why they cannot be connected as an open-delta. If they can be reconnected open-delta, what would be the output capacity of the two remaining transformers?
2 (a) Why the primary winding of the distribution transformer used in electrical installation in building is always connected in Delta, while the secondary is always connected in Wye! (b) A wye-connected three-phase generator supplies power to a delta-connected resistive load (see the Figure Q2). Each impedance load of the delta connected load equals Zas given bellow. Alternator Ep Ip EP Ip EL EL IL j42 Figure 02 Find the following values: EPLoad)- phase voltage of the load IpLoad)- phase current of the load Inoad)- line current to the load ILAR)- line current delivered by the alternator IPIAK)- phase current of the alternator EPIAN) - phase voltage of the alternator P - true power consumed by the load if the load is purely resistive with resistance of 32
A 100-kVA 400/2000-V single-phase transformer has the following parameters: R = 0.01 N R2 = 0.25 N X1 = 0.03 N X2 = 0.75 N %3D G = 2.2 ms Bm = -6.7 ms %3D Note that Ge and Bm are given in terms of primary reference. The transformer supplies a load of 90 kVA at 2000 V and 0.8 PF lagging.
Explain step by step please a b and c
Please asap And in details