Allday - Allday 24 0/P Allday 24 0/P+ (Piran) 24 (Pew) 241 Q1- the primary voltage of transformer is 6600 V and the turn ratio equal 10.6. If the primary and secondary impedances are Z₁=1.4+j5.2, Z₂= 0.0117+J0.0465 respectively. Find the output power when the load draw 300 A at 0.8 lag p.f. ANS. 144 KW Q2- 100 KVA, (6600/330),single- phase transformer, the primary connected to supply voltage 100 V and the secondary side short-circuit. The transformer drawn 10 A and 436 watt. calculate the voltage applied to primary winding at full load with 0.8 lag p.f to make secondary voltage 330 V. ANS. 6734 V

Allday - Allday 24 0/P Allday 24 0/P+ (Piran) 24 (Pew) 241 Q1- the primary voltage of transformer is 6600 V and the turn ratio equal 10.6. If the primary and secondary impedances are Z₁=1.4+j5.2, Z₂= 0.0117+J0.0465 respectively. Find the output power when the load draw 300 A at 0.8 lag p.f. ANS. 144 KW Q2- 100 KVA, (6600/330),single- phase transformer, the primary connected to supply voltage 100 V and the secondary side short-circuit. The transformer drawn 10 A and 436 watt. calculate the voltage applied to primary winding at full load with 0.8 lag p.f to make secondary voltage 330 V. ANS. 6734 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A patient is connected to a pressure monitor by way of a catheter. Resistance of catheter is 6000 Q. Dirt and grime make a resistance path from the catheter to H wire of 500,000 Q. The H wire is plugged into a 240 V power bus. Calculate the leakage current that could pass into the heart of the patient. Is the patient might or might not have shock? Assume a viscera resistance of 200 Q.
Calculate the voltage at a distance of 200 m of a 300 m long distributor uni formly loaded at the rate of 0.75 A per metre. The distributor is fed at one end at 250 V. The resistance of the distributor (go and return) per metre is 0.00018 ohm. Also find the power loss in the distributor.
Needs Complete typed solution with 100 % accuracy.
Solution of part (d).
The subject is Basic Electronics. Please make the solution clear and understandable.
A device used to protect a circuit against over currents is a what? a. Polyswitchb. Capacitorc. Dioded. Resistor
By using a mass scale, five readings were taken to measure a mass of 50 Kg as follows: (50.8, 50.9, 50.7, 50.6 and 51) Kg. For this measuring instrument and according to the fifth reading, the precision is..............
Question 1 Consider the adjacent circuit diagram of three different rectifier topologies connected to an 373 Volt three-phase AC system. Assume a load resistance of 36Ω in ALL instances with NO losses in the rest of the circuit. Observe the connections to the AC supply and determine the parameters for, Rectifier B: 1.1) the maximum voltage across the load and the dc load voltage and the r.m.s. load voltage. 1.2) the rectification efficiency and the r.m.s. current rating of the diodes. 1.3) the conduction period of a single diode and the PIV rating of the diodes.
The illustration below shows the components of a simple circuit diagram.choose from the choices on the left the best term or description that will match each component and the function.write your answer on the prescribed box
(a) A d.c bridge based on strain gauge sensor is used to measure the vehicle weight. The vahes of Vac =5 V, R1, R2, and R3 is 150 k2. The vahue of stram gauge, R4 before loaded is 150 k2. Before the measuurement, a standard load with weight of 6000 kg is used for calbration. The galvanometer, I, is flowed about 2.25 uA. Analyse the crcuit to determine vahues of R V and R when it is loaded. Assume the vahue R of galvanometer is zero. R1 R3 Vác R2 Figure Q4
Please solve Last time give wrong solution. A resistance wire strain gauge uses a soft iron wire of small diameter the gauge factor is + 3.6. Neglecting the piezoelectric resistive effect. Calculate the Poisson ratio.