A thin-walled, two-cell aluminum tube, symmetric with the y and z axes, is transmitting a torsional moment of 2.5 kN-m. The thickness of each wall is 5 mm. For aluminum let E= 70 GPa and v=0.33. Determine the average shear stress in each wall and the angle of twist per unit length. 25 R

Q: The aluminum machine part is subjected to a moment of M-95 N-m. (Eigure 1) 10 mm 10 mm nm 20 mm 10…

A:

Q: Assume A is pinned and B is a roller in (Eigure 1). Take that w = 9.0 kN/m. Determine the normal…

A:

Q: Two vertical forces are applied to a simply supported beam, having the cross section shown. Assume…

A:

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure  Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2  ×  r^2 +…

Q: c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m…

A: Given Data The daimeter of truss tie rod is:d=9.52 mm The length is:l=1.75 m The stress experienced…

Q: Calculate the stress concentration factor (kt). the small diameter is 0.88 in and the bigger one is…

A: Given:The small diameter is the bigger diameter is The radius is The moment is The torque is

Q: Problem 1: In the figure below a solid bar with a 1.00 in diameter is subjected to a bending moment…

A: Given data, Diameter of the solid bar, d = 1 in Twisting moment and bending moment are equal, i.e.,…

Q: as depicted in the figure. As

A: given:

Q: Rockwell hardness . figure 6.19 Rockwell hardness Tensile strength = 0 MPA Tensile strength = 0 ksi…

A: (a)

Q: Example: A bar with a rectangular cross section and two U-notches F w = 90 mm h = 15 mm 6 mm r- F w…

A: Width of the bar,(w)=90 mm. Height of the notch,(h)=15 mm. The radius of the notch, (r)=6 mm. The…

Q: A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal…

A: b = 60 mm c = 40 mm R = 5 mm to determine diameter dmax of the largest hole

Q: Determine the bending stress developed at corner B. Take M = 46 kN m

A: Given datathe applied moment M= 46 KN. mFind Outa) The bending stress developed at corner Ab) The…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Eigure 1)

A:

Q: A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear…

A: A solid steel bar of circular cross section has diameter d = 40 mm = 0.04 m, length L = 1.3 m and…

Q: A shear force of S, = 35 kN is applied a distance of a/2 to the left of the vertical mid-line, as…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the…

A:

Q: calculate the magnitude of the shear stress at the point due to internal shear on the section.…

A: To calculate the normal stress, internal bending moment and shear stressthe following data istensile…