A tapered circular rod of diameter varying from 30 mm to 20 mm is connected to another uniform circular rod of diameter 10 mm as shown in the following figure. Both bars are made of same material with the modulus of elasticity, E = 4x10^5 MPa. When subjected to a load P = 40 kN, the deflection at point A is........mm. 2m d₁ 1.5m = 30mm d₂=20 mm A P = 40TKN

A tapered circular rod of diameter varying from 30 mm to 20 mm is connected to another uniform circular rod of diameter 10 mm as shown in the following figure. Both bars are made of same material with the modulus of elasticity, E = 4x10^5 MPa. When subjected to a load P = 40 kN, the deflection at point A is........mm. 2m d₁ 1.5m = 30mm d₂=20 mm A P = 40TKN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The prismatic block with dimensions a * b * c is placed in a rigid space of the same size. Find the force P required to shorten the block's z Anchor by 2.0 mm. a=5cm b=6 cm c =1.8m poisson rate= 0.3 modulus of elasticity=200000 MPa
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1250 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3780 μrad. Assume a = 2.1 mm. Calculate the magnitude of dimension b in the figure. h a Answer: b = i A W B mm X
The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load P is applied. If the value of P is 60 KN, the elongation in the Aluminum Bar is Steel L= 4 m Aluminum L= 3 m A= 500 mm E = 70 GPa A = 300 mm E = 200 GPa A 3.5 m 2.5 m P
FINITE ELEMENT METHODS
What is the area of the tube? What is the total length of the median line? What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object?
Problem # 8: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson's ratio to be 0.33. Determine the value of loads P and its axial deformation. d = 12 mm P L 1.20 m P
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1200 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3650 µrad. Assume a = 1.8 mm. Calculate the magnitude of dimension b in the figure. D Answer: b= i W B a mm X
Mechanics of deformable bodies. Two decimal places.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.72 mm the values of elastic modulus for steel is 223 MPa. Take H1 = 7 cm, H2 = 10 cm, top bar (R) is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure.[a = 200 mm, b = 202.1 mm, c = 198.9 mm] For the deformed plate, determine the normal strain of diagonal PR? In micro £ For the deformed plate, determine the shear strain xy at corner P?in micro rad
Q 2. For the symmetrical section in figure 2 shown below, calculate B mm 350 mm 0.8 B mm Figure (2) (i) The elastic section modulus (Z) (ii) The Plastic section modulus (Zr) (iii) Shape factor (S) (iv) Plastic moment given fy- 262 N/mm2 B= 202