A tapered bar AB of solid rectangular cross-section with a thickness of 20 mm and length L = 800 mm is supported at the end B and subjected to tensile load P = 25 KN at the free end A. The width of the bar at ends A and B are 50 mm and 75 mm, respectively. Determine the elongation of the bar due to load P. Use E = 200 x 10° Pa. Use integration to solve this problem. В A P < L-

A tapered bar AB of solid rectangular cross-section with a thickness of 20 mm and length L = 800 mm is supported at the end B and subjected to tensile load P = 25 KN at the free end A. The width of the bar at ends A and B are 50 mm and 75 mm, respectively. Determine the elongation of the bar due to load P. Use E = 200 x 10° Pa. Use integration to solve this problem. В A P < L-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8 4. Complete the following a. Draw Mohr's circle for the element given and label the axes b. Determine 01, 03, and Tmax for the element -4 c. Determine the stresses (on, Tn) on the plane shown d. Plot the point representing the plane with stresses (On, Tn) on the circle Tn 5 40 5 8
The cross-sectional dimensions of a beam are shown. Assume b-1.875 in., t-tw-0.125 in. and d=2.75 in. (a) If the bending stress at point K is 3340 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o, at point H (positive if tension, negative if compression). H K Answers: bf (a) M₂ = i (b) σH = tw lb-ft. psi.
The truss in Figure 4 is loaded as shown. Both the nodes 1 and 5 are hinged supports. Take P = 27.8, L = 2.7, A = 0.0015 m2 and E=200 GPa. AE is constant for all the members. Use the stiffness method approach to solve parts (a) to (d) below. Write down your P and L values and answer parts a) to d) below. (a) Determine the stiffness matrices of the truss members 1, 4 and 5 in the global co-ordinate system with the origin at node 1. Use the member directions shown and clearly indicate the corresponding degrees of freedom numbers in the stiffness matrices. (b) Determine the stiffness matrices of elements 1 and 4 in the local co-ordinate system and then convert the respective local stiffness matrices to the global stiffness matrices. Show all calculations. Check the results with those obtained in part (a) above and comment. (c) Determine the load vector (Q) and displacement vector (D) and write the load-displacement relationship for the entire truss in the global co-ordinate…
A bar AB (A = 500 mm²) is hinged at A and is supported by a rod CD and C. The rod is pin connected at A, as shown. Neglect deflections of the bar due to bending. If the diameter of the rod connecting the load W = 90 kN is 20 mm, what is the displacement of the load? Use E=210 38 mm. 2m Diameter 1.8m GPa. wwww A 2.5 m 1.5m 0.6m W=90KN
Read the question carefully and give me complete right solution according to the question. Don't miss anything.
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 7.0 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at A. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1 m
A rectangular beam has an extended cantilever beam the is attached at the end of the beam. A force P = 165,000 N is acted at the end of cantilever beam. Take S1 = 230 mm, S2 = 300 mm. What is the angle of twist of the beam if the length of the beam is 1500 mm, G = 2.0 MPa. Show complete solution with FBD
4. The rigid bar AB is supported by two rods as shown and is horizontal before the load P is applied. Determine the vertical displacement of point which is 2 meters from the left support caused by the load P = 68 kN. Neglect the weight of the bar and the rods. Aluminum L= 3 m A = 300 mm? E= 70 GPa Steel L=4 m A= 500 mm? E= 200 GPa 3.5 m 2.5 m
g) the value of the constant of integration C4. Enter your answer in kNm3 to 3 decimal places.
SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem II. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 10 mm4 for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. 5 m 2 m Aluminum -Steel 2 m C
In figure shown the cross-sectional area of BD and CE is 2 mm?, E = 210 GPa, L = 350 mm, L2 = 200 mm, a = 300 mm, b = 400 mm and c = 250 mm. a. Determine the deflection of end A of the rigid member ABC caused by the P = 600 N load. b. Determine the maximum value of P if the allowable deflection at A is 2.5 mm and the allowable stresses of the rods is 120 MPa. L2 b.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; / = 1930 in.41. For the loading shown, determine: (a) the beam deflection at point A (b) the beam deflection at point B. Assume MA = 250 kip-ft, P = 29 kips, LAB = 4.9 ft, LBc = 7.4 ft.