A T-beam has the following properties: bf = 820 mm, bw = 250 mm, d = 470 mm, t = 100 mm. f’c = 20.7 MPa, fy = 414 MPa. Determine the required tension steel area when: a.MD = 175 kN-m, ML = 190 kN-m b.Find the maximum design moment so that its tension controlled. (USE c = 3d/8). Tension steel exactly experiences 0.005 strain. hello please answer that question,,thank you God bless

Q: Determine the gross area of steel needed to design the bar force members at BC, BE, and AE. Stress…

A: Determine the gross area of steel needed to design the bar force members at BC, BE, and AE.

Q: 4. Determine the force in each of the member of state if the members are in tension or compression.…

A: Determine the force in each of the member of the truss

Q: Find the stresses in members BC BD and CF for the truss shown. Indicate the tension or compression.…

A: We will use method of joints

Q: -5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force…

A:

Q: E Bars AB CD are rigid. The supports are pins at A and C and the Steel. What maximum force P can be…

A: Maximum force P

Q: Determine the required tension steel area for a rectangular beam with given properties below, d'…

A: Given  d= 475mm  Fy = 400 Mpa

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A:

Q: Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000…

A: a )  P = 9000 lb and F = 3000 lb Compute the stresses at A and B  ? Solid mechanics problem.

Q: Determine the smallest safe cross-sectional areas of members CD, CI and CH for the truss shown. The…

A:

Q: 4. Find the stresses in 3 m members BC, BD and CF for 3 m 4 m A the truss shown. Indicate 40 kN 70…

A: The free body diagram of truss ABCD:

Q: please someone answer this with complete solution thank you

A:

Q: Assuming A36 steel, select the most economical W8 section. Check the shear stress, and determine the…

A:

Q: < 250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars…

A: E=2G(1+μ)μ=E2G-1 GIVEN E=205GPa G=82GPa NOW USING ABOVE FORMULA μ=2052x82-1 μ=.25

Q: THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH!…

A:

Q: Check the stability of truss.. Give me right solution with clear calculations.

A:

Q: please solve this with complete solution. Thank you

A:

Q: PART 2 : COMPUTE THE AXIAL STRESSES IN ALL MEMBERS OF THE TRUSS SHOWN. USE 300 sq. mm AND 250 sq. mm…

A: Question is based on truss supported on roller and hinged support. Span length of member and loading…

Q: Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: to find stress in each rod

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: To find stress in each rod

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength : Yield strength of an element is a maximum stress an element or component can bear…

Q: Question 3. in the truss shown, a-5m, b 4m, and c=4 m Determine the force in member BE is kN. Use ve…

A:

Q: don't

A:

Q: Consider the simply supported truss as defined in the figure and parameter table. Find the force in…

A:

Q: Determine the nominal strength for tensile yielding in the gross section. 1. B. 429.67 KN D.390.10…

A:

Q: Find the forces in all members of the truss that shown in Figure II and determine whether they are…

A:

Q: Members of the following 2-DOF beam system have the same El and length L C. Which of the following 4…

A: Since K12= K21 Hence Statement C and D are Correct Stiffness caused due to rotation such as K11and K…

Q: the

A: A device for measuring corneal thickness that is installed on a slit-lamp is known as pachometer. It…

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

A:

Q: 400 Ib 300 so ib D

A:

Q: STRENGTH OF MATERIALS PLEASE WRITE THE SOLUTIONS LEGIBLY AND USE 4 DECIMAL PLACES. RATE WILL BE…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: or the beam shown, determine the stress in each rod if the load P= 50 kN is applied. Bronze Steel…

A:

Q: One1 the are two For thickness Subjected ponts Subjected aN/m. is the retanglugar plate all…

A: To find - Equilibrium equation of the structure.

Q: For the truss shown, calculate stresses in members AC, AB and BE. Cross section of each member 16…

A:

Q: "Determine thé forcés in all the members, and state if these meņmbers are in tension or compression.…

A:

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

A:

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data  Using method of section

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: to find stress in each rod

Q: Determine the required tension steel area for d' = 75mm b = 350mm d = 470mm fc' = 30MPa fy = 400 MPa

A:

Q: 13 lb, y = 7.94 ft, and the stress in the member is 12.47 ksi . Round off the final answer to two…

A:

Q: Solve the forces in each members in terms of the force P. Follow the format of the table below…

A: Consider the free body diagram of the truss shown below. Consider the moment equilibrium about…

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.