THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH! STRENGTH OF MATERIALS PLEASE WRITE THE SOLUTIONS LEGIBLY AND USE 4 DECIMAL PLACES. RATE WILL BE GIVEN. Instructions: a. Draw the FBD OF EACH member. b. SOLVE FOR THE REACTIONS c. SOLVE THE CROSS-SECTIONAL ARE OF THE MEMBER d. SOLVE THE AXIAL FORCE ON THE MEMBER AND IDENTIFY WHETHER IT IS TENSION (T) OR COMPRESSION (C). e. Solve for the NORMAL STRESS ON THE MEMBER f. Identify the number of rivets from the shearing of rivets. g. Identify the number of rivets from the Bearing of the Gusset Plate and Rivets. h. What is the governing number of rivets per member. 40 kN B 4m 40 kN A 70 kN E L100X75X13 C 4m Diameter of rivet = 16 mm Thickness of gusset plate = 20 mm Allowable Bearing Stress = 95 MPa Allowable Shearing Stress = 125 MPa Allowable Bearing Stress = 95 MPa F 6 m

THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH! STRENGTH OF MATERIALS PLEASE WRITE THE SOLUTIONS LEGIBLY AND USE 4 DECIMAL PLACES. RATE WILL BE GIVEN. Instructions: a. Draw the FBD OF EACH member. b. SOLVE FOR THE REACTIONS c. SOLVE THE CROSS-SECTIONAL ARE OF THE MEMBER d. SOLVE THE AXIAL FORCE ON THE MEMBER AND IDENTIFY WHETHER IT IS TENSION (T) OR COMPRESSION (C). e. Solve for the NORMAL STRESS ON THE MEMBER f. Identify the number of rivets from the shearing of rivets. g. Identify the number of rivets from the Bearing of the Gusset Plate and Rivets. h. What is the governing number of rivets per member. 40 kN B 4m 40 kN A 70 kN E L100X75X13 C 4m Diameter of rivet = 16 mm Thickness of gusset plate = 20 mm Allowable Bearing Stress = 95 MPa Allowable Shearing Stress = 125 MPa Allowable Bearing Stress = 95 MPa F 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 Locate the centroid of the shaded figure. Y 4.38 4.38 1.50 2.00 1.50 3.00 8.00 4.00 2.50 4.76 4.00 Enter your answer
In the following table, a part of a project, for which the time period for each activity is specified, find the time required to complete the project using the network diagram by Act. on arrows. Activity A B D G H I Time Followed by Preceded by B.C 23573625 G.F D.F E I I H I A A C B.C DBG H.E.F
). The network and durations given below show the normal schedule for a project, and the table given below summarizes the time-cost information for the activities, the owner wants to finish the project in 110 days, so find the minimum possible cost for the project to finish in 110 days AND 20 A B C D (19) E F 9. Activity (days) 120 20 40 30 50 60 Normal du 120 60 Crash (days) 100 15 30 20 40 45 30 on 4 50 Norma Cost 12000 1800 16000 1400 3600 13500 Cost 14000 2800 22000 2000 4800 18000
Question 4: Determine the amount of time in weeks that gives a probability of 97.5% until the seventh event in the following grid, and then find the following: What is the probability of completing the project with a period less than TE by 4 weeks What is the probability of completing the project with a period of more than TE by 2 weeks Act. 1-2 2-3 2-5 2-4 3-4 3-7 5-6 6-7 4-7 0 8 4 7 7 4 7 10 10 4 M 10 5 8 9 6 8 14 14 5 24 12 21 11 8 15 24 24 12
Please answer the remaining 2 questions. D and E
Question 4 Given that y= 5t3+7 and x =F-5 Find y" when x-6. Express your answer in whole number A Moving to another question will save this response. acer
O 110 LIZAIN IQ Your email address will be recorded when you submit this form. Not ced20211258@almaaqal.edu.iq? Switch account 0.2/ Choose the correct option from these questions, (options). Pistol bullet is shot upward from the earth with initial speed of 25 m/sec. How high is it when its final speed is 5 m/sec. O 28.9 m O 30.58 O 33.129 m O 25.9 m What is the average power must produce to accelerate car with 1500 kg from GHADEER C 4:04p äc lul 21.03.15 A
Logged in as zenuh. Log Out webwork / mat228-rosen / homework 2/6 Homework 2: Problem 6 Problem List Next Problem Previous Problem (1 point). The distance d of a point P to the line through points A and Bis the length of the component of AP that is orthogonal to AB, as indicated in the diagram. So the distance from P = (4,0, –3) to the line through the points A= (2. –2. 4) and B = (-1, –5, –2) is Preview My Answers Submit Answers Show me another You have attempted this problem 15 times. You have 5 attempts left before new version will be requested Your overall recorded score is 0%. You have unlimnited attempts remaining. Reflect in ePortfolio Download Print Activity Details You have viewed this topic P Type here to search 立 Community
6. For the data in Problem 5 of Chapter 6, calculate 6 σ, Cp, and Cpk. Interpret the indices. The specification limits are 50 +/- 0.5. 225.00 226.00 227.00 226.00 227.00 228.00 228.00 229.00 222.00 223.00 224.00 226.00 227.00 228.00 225.00 221.00 227.00 229.00 230.00
Please answer with explanation Thank you so much
Hi, could you please further elaborate (concise and understandable) on how did that person get the final answer especially on 2.14kN, 7.47kN, 5.33kN, and 21.33kN. I get this photo from youtube. He/She didn't explain how she/he got the final answers. He/She only explained the summation or how he/she get the equation. note: I will dislike it if your explanation in the final answers isn't elaborated and not easy to understand.
the answer choices are given in the picture.... the answers provided are not even options from the picture