A student reacted 49.3 mL of 1.0 M HCl at 20.0°C with 48.7 mL of 1.5 M NaOH at 22.0°C, after the reaction the final temperature was 27.58°C. Assuming the specific heat capacity is the same as water, where Cs is 4.184 J/g°C, and that the density is 1.00 g/mL, determine: a)the heat of the physical solution b) the heat of the reaction c) which species is the limiting reactant d)the enthalpy of reaction in Kj/mol

A student reacted 49.3 mL of 1.0 M HCl at 20.0°C with 48.7 mL of 1.5 M NaOH at 22.0°C, after the reaction the final temperature was 27.58°C. Assuming the specific heat capacity is the same as water, where Cs is 4.184 J/g°C, and that the density is 1.00 g/mL, determine: a)the heat of the physical solution b) the heat of the reaction c) which species is the limiting reactant d)the enthalpy of reaction in Kj/mol

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Phoose which of the following has the least4s . Omolten brass (alloy of Cu and Zn) Omethane Laqueous solution of KBr Umetallic Pt
What volume of 0.12 M Na2SO4 will be required to react with 10 mL of 0.05 M CrCl6?
. So, we need 5.00 mmol of base (titrant) to be delivered to the analyte. Since we know the molarity of the base and moles of base, we just need to solve for the volume of base (titrant) to be added. molpase Mpase = Voladded Molarity base =. 0.150 (M) Moles of base = _5.00 (mmol) Volume of base needed to reach equivalence point _ (mL)
Given an original 6.17 M Cu solution (solution 1), and a second solution made by a serial dilution of the original solution by pipeting 5.00 mL into a 500 mL volumetic flask to make a second solution (solution 2). Calculae the log [concentration ratio] for the 2 solutions.
concider the reaction: 3KOH+H3PO4---> K3PO4+ 3H20 a 41.2ml sample of koh solution of unknown concentration requires 26.3ml of .165M of H2SO4 solution to neutralize what is the molarity of the KOH solution please show work and sig figs thank you
For a 50ml beaker, 0.4532g of pure iron III oxide was weighed, to which 1 ml of a concentrated hydrochloric acid solution was added and then 20 ml of deionized water was added to the beaker. After mixing, the resulting solution was transferred to a 50.00 ml flask and the volume was made up with deionized water. Then 15ml of this solution into a second beaker to which 10ml of an iron iii chloride solution of 0.200 M concentration was added. Calculate the final concentration of the iron iii cation solution expressed in mol/L and in g/L, considering that the volumes are additive.
The gravimetric determination of Ni2*: Ni (58.7 g/mol) was precipitated as Ni(DMG) : (288.7 g/mol). The volume of unknown solution in the sample -60.00 mL. The mass of empty crucible 30.107 g, the mass of empty crucible and precipitate = 30.300 g. Calculate the concentration of Ni* in the unknown in sample solution (in mg/L) is: 1. 0262X10 2. 0131X 10 3. 025.3X 10+ 4. 00.654X 10
A stock solution whose concentration is 25.00 mg/mL was provided. A primary standard solution was then prepared by transferring 5.00 mL of the stock solution into a 50.00 mL volumetric flask. The primary standard solution was used to prepare three standard solutions of different concentrations by taking different volumes of aliquots into three 25.00 mL volumetric flasks: Standard Solution #1 #2 #3 Amount of Primary Solution (mL) 5.00 10.00 15.00 Three 25.00 mL volumetric flasks were then diluted to mark with water. Questions #1 What is the concentration of the primary standard solutions, expressed in units of mg/ml? #2 Re-write the concentration of the primary standard solutions obtained from Q#1 in units of μg/mL. #3 Determine the concentrations of three standard solutions in units of µg/mL. #4 What is a requirement for a "blank" solution used in calibration in spectrophotometry? Page 5 (Experiment #3)