A steel cylinder with 400 mm outside diameter and wall thickness of 25 mm is filled with concrete and used as a pier to support an axial load in compression. If the allowable stresses are 150 MPa for steel and 18 MPa for concrete and if the modulus of elasticity for steel is 200 GPa and for concrete is 19.2 GPa, What is the allowable load for the pier?

A steel cylinder with 400 mm outside diameter and wall thickness of 25 mm is filled with concrete and used as a pier to support an axial load in compression. If the allowable stresses are 150 MPa for steel and 18 MPa for concrete and if the modulus of elasticity for steel is 200 GPa and for concrete is 19.2 GPa, What is the allowable load for the pier?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the dead load due to concrete per foot length of beam if concrete specific weight is 30 kN/m3
Hi can you please complete the question fully thanks so much
1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.
The floor of a classroom is made of 150-mm thick lightweight concrete. If the floor is a slab having a length of 8m and width of 6m, determine the resultant force (in KN) caused by the dead load, the live load, and the total load. Note: lightweight concrete is 0.015KN/m2 per mm thickness & classroom is 1.92KN/m2
A concrete beam of length 5.5m is built monolithically with the slab. Originally, the beam has a width of 300mm and effective depth of 400mm. If the flange of the slab is 150mm and the total area tension steel bars is 500 sq.cm., determine the design capacity of the beam structure. The concrete has a compressive strength of 25 MPa, steels' yield strength is 420 MPa. and the beam's clear span from its adjacent beams is 2.15m.
A composite beam 225 mm wide x 300 mm deep x 4 m long is made by bolting two 100-mm- wide x 300-mm-deep timber planks to the sides of a 25 x 300-mm structural aluminium plate. The moduli of elasticity for the timber and aluminium are 8 GPa and 73 GPa, respectively. Determine the maximum tensile flexural stress in each of the materials if the composite beam is simply supported and carries a concentrated load 30 kN in the centre of the beam. 100 mm 25 mm 100 mm 11 300 mm
A rectangular beam has a width of 380 mm, effective depth of 445 mm, and overall depth of 510 mm and is reinforced with four No.29 tension bars. The concrete modulus of rupture fr = 3.65 MPa. The elastic modulus of the concrete and steel are, respectively, Ec =27,800 MPa and Es= 200,000 MPa. Determine if the beam will show hairline cracks due to a bending moment M = 108 kN-m and compute the relevant stresses. Provide material properties for concrete and reinforcing steel used in your design.
A timber column, 8 in. × 8 in. in cross section, is reinforced on each side by a steel plate 8 in. wide and t in. thick. Determine the thickness t so that the column will support an axial load of 300 kips without exceeding a maximum timber stress of 1200 psi or a maximum steel stress of 20 ksi. The moduli of elasticity are 1.5 × 106 psi for timber, and 29 × 106 psi for steel.
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
A reinforced concrete T-Beam has a width of 800mm and a thickness of 50mm. It has an effective depth of 300mm and is reinforced at the bottom with a total steel area of 1800sq.mm. If the web thickness of the T-beam is 200mm, with a concrete strength of fc' = 20MPa and yield strength of steel fy= 400MPa. Assume steel yields. The value of the area subjected tocompressive stress is _sq.mm A. 42,353 sq.mmB. 42,553 sq.mmC. 42,153 sq.mmD. 41,953 sq.mm
A rectangular concrete beam of cross section 100mm wide and 400mm deep is prestressed by a straight cable of span 6m, imposed load is 3.14kn/m, area is 36×10³mm²(Z=18×105mm³). Calculate working moment assuming the self weight of concrete as 24kn/m³?
Maximum strain in concrete taken for design is 0.0040 while strain in deformed bar is calculated with an offset at 0.0015. A beam has an effective depth of 550 mm and is reinforced with Fe415 steel. What would be the value of limiting neutral axis depth (in mm) for this beam?