A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress is 490 MPa. and the factor of safety is 2.5. Determine the required thickness I to the nearest millimeter.

Q: Bar (1) in Figure PP1.2-6 has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be…

A: The free-body diagram of the forces acting on the bar ABC is given below. From the given data, the…

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

A:

Q: d= 1.50 in. t=0.875 in. P= 7300 lb What is the average bearing stress produced in the support…

A:

Q: A thick walled cylinder with an inner diameter 44 mm and an outer diameter 70 mm is made from a…

A: To find: The pressure will the cylinder initially yields. Given: The inner diameter is di=44 mm and…

Q: The cross-sectional area of the figure below is 0.5 in2. If E = 13 x 106 psi, calculate the total…

A:

Q: 40 MPa 35 MPa -60 MPa Figure 1 Due to the applied loading, the element at one point on the solid…

A:

Q: Figure Part A 3 kip μà -1.5 ft d= Value Determine the minimum diameter d of the rod to safely…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S = 75 MPa and Sy =…

A:

Q: . A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given   Tensile modulus, E1 = 10 GPa                              E2 = 0.4 GPa Find   Tensile…

Q: 7. A thick-wall cylinder is made of steel (E-200 GPa and v=0.29), has an inside diameter of 20 mm,…

A:

Q: ▾ Part B Determine the normal stress dy'. Express your answer to three significant figures and…

A:

Q: An AISI 1020 steel rod 22 feet long is anchored between two rigid supports. At 90 degrees Fahrenheit…

A: For AISI 1020 steel rod, E=29000 ksi=29×106 psi and α=6.5×10-6 in/in.°F. Let Ti be the initial…

Q: Ql: A bar ABCD shown in Figure (1) below consists of three sections: AB is of 42 mm diameter and 80…

A:

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data  height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: The steel bar has the dimensions shown. (Figure 1) Figure 30 mm 24 mm 20 mm o k 60 mm - 15 mm 1 of 1…

A:

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: material is 280 MPa. Using a safety factor of 1.5, determine the material thickness of the tank in…

A:

Q: ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

A:

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length…

A:

Q: The gap of 0.5 mm in the element given in the figure is formed at 20 C. What is the temperature…

A: Given: ∆l=0.5 mml=0.45 mA=1800 mm2E=73GPaα=12.9×10-6 /°C

Q: In the picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”.…

A: Sy=400 MPa

Q: See the set of bars for made of a material that has a yield strength of 350 MPa, determine the…

A:

Q: A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both…

A: Given Data The wall thickness is:hwall=6 mm The external diameter of the brass tube is:De=750 mm…

Q: A cantilever beam, 100 mm wide by 230 mm high and 7 m long, carries a load that varies uniformly…

A: Due to bending in a beam , there are two types of stresses acting in a beam which are- 1. Bending…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

A:

Q: Question 2 For the stresses of plane stress state is ox = -8 MPa , Oy = 7 MPa and Txy = -6 MPa Draw…

A:

Q: 60 MPa 30 MPa 45 MPa

A: On the given element, Stress in x direction = σx = 45 MPa Stress in y direction = σy =  -60 MPa…

Q: Consider the frame in (Eigure 1). The crate weighs 400 lb. Follow the sign convention Figure 4ft |_…

A: According to the given data A loading structure is provided in the question. We need to find…

Q: The member has a cross section with the dimensions shown, and is subject to an internal moment Mof…

A:

Q: Part A Determine the average normal stress acting along section a-a. Express your answer to three…

A:

Q: A circle of 250 mm diameter is scribed on a steel plate. The plate is subjected to a tensile stress…

A:

Q: A cylindrical shell is pressurised to 2 kN/mm², and has an internal diameter of 556 mm. If the…

A:

Q: Question 1. P T The figure (not drawn to scale) shows a cylindrical column submitted to a combined…

A: Consider σx be the normal stress in x-direction and τxy be the torsional shear stress in xy-plane.…

Q: If the steel rod shown is acted upon as shown, Compute for the total deformation of the rod. Assume…

A:

Q: A 40 mm diameter aluminum cylinder and 20 mm diameter steel cylinder are positioned snugly between…

A:

Q: A machine member part is subjected to fluctuating stress of σ = ax cos(8nt) The endurance limit of…

A: Given:Fluctuating stress, σ=σo cos8πtendurance limit=350 MPAFOS=3.5Find,maximum value of  σo

Q: The lever is attached to the shaft A using a key that has a width d and length of 26 mm If the shaft…

A: Given  F = 200 N Width = d  Length (L) = 26 mm  Shear stress = 37 MPa

Q: A cantilever beam, 80 mm wide by 260 mm high and 9 m long, carries a load that varies uniformly from…

A: Width of the cantilever beam, B= 80 mm Height of the cantilever beam, H= 260 mm Length, L= 9 m At…

Q: The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L = 460 mm, H = 345…

A: GIVEN DATA-  A DEFORMED PLASTIC SHAPE GIVEN  WE HAVE TO FIND SHEAR STRAIN AT A AND B

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.