A special-purpose fluid flows at 4 x 102 kg/s inside a 1 cm diameter tube that is heated electrically at a constant rate of 50 W/m. At a specific location vere the flow and heat transfer are fully developed, the wall temperature is 400 K. At this location, calculate the mean temperature of the fluid. The fluid has the following properties: thermal conductivity = 0.125 W/m-K, density 875 kg/m, kinematic viscosity = 40x106 m2/s, and specific heat = 2120 J/kg-K. %3!

A special-purpose fluid flows at 4 x 102 kg/s inside a 1 cm diameter tube that is heated electrically at a constant rate of 50 W/m. At a specific location vere the flow and heat transfer are fully developed, the wall temperature is 400 K. At this location, calculate the mean temperature of the fluid. The fluid has the following properties: thermal conductivity = 0.125 W/m-K, density 875 kg/m, kinematic viscosity = 40x106 m2/s, and specific heat = 2120 J/kg-K. %3!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 50°C flows through an automobile radiator tube 0.5 cm inner diameter, 50 cm long with a mean velocity of 1 m/s. The surface of the radiator tube is at 30°C. Determine the heat transfer coefficient using Colburn Analogy. [Use friction factor f=0.316 Re/5 for turbulent and f=0.184 Re4 for laminar.] The property values of Water at 50°C and 40°C are 50°C 40°C Density (kg/m³) 990 995 Cp (kJ/kg K) 4.182 4.179 k (W/m K) 0.640 0.628 V (m/s) 5.67 x 10"| 6.57 × 10" Pr 3.68 4.34
Water is to be heated from 35 °C to 65 °C in a rough tube with a relative roughness of 0.001. The tube has an electric heater provides a constant heat flux such that the tube average wall temperature is 20 °C above the average water bulk temperature. The Reynolds number used for calculating the heat-transfer coefficient is 100,000. Calculate the length of tube required for heating, expressed in meters, if the tube has a diameter of 1 cm.
Geothermal steam at 172°C condenses in the shell side of a heat exchanger over the tubes through which water flows. Water "C 4201 J/kg.K, k = 0.673 W/m.°C, p = 968.1 kg/m , µ = 3.33E-4 Pa.s, Pr = 2.08" enters the 4-cm-diameter, 9.5m-long tubes at 20°C at a rate of 0.3 kg/s. What is the exit temperature of water “°C"? Assume fully developed flow, if turbulent flow %3D %3D use, Dittus-Boelter equation: Nu = 0.023 Re Pr. us,8 %3D Select one: А. 150.71 B. 139.86 C. 143.40 D. 147.09 Е. 154.18
Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 149oF and length of 10 m. Surface conduction of hot fluid is 5.2 W/m2-K and thermal conductivity of brass is 12.84 W/m2-K. Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84 W/m-K. Outside of it, is a fluid with 45oC with surface conductance of 3.2 W/m2-K. Find the heat transfer from the hot fluid with temperature of 149oF to fluid with temperature of 45oC.
An electric resistance heater is embedded in a long cylinder ofdiameter 30mm. When water with a temperature of 25 C and velocityof 1m/s flows crosswise over the cylinder, the power per unit lengthrequired to maintain the surface at a uniform temperature of 90 C is28kW/m. When air, also at 25 C, but with a velocity of 10m/s isflowing, the power per unit length required to maintain the samesurface temperature is 400W/m. Calculate and compare the convectioncoefficients for the flows of water and air.
A thick concrete wall having a uniform temperature of 50oC is suddenly subjected to a stream of water so that the surface temperature is suddenly lowered to 15oC. How long will it take to cool the concrete to 30oC at a depth of 5 cm from the surface? Data: concrete properties, k = 1.37 W/m×oC, r = 2100 kg/m3, a = 7.5×10-7 m2/s.
A 7 cm diameter bed on a 25 cm long bed, as shown in the figure below. The shaft rotates at 3200 revolutions per minute with uniform intervals of 0.2 mm. Continuous operation The temperatures of the shaft and bearing adjacent to the oil gap are 55 0C. your oil viscosity 0.05 N.s/m2 and its thermal conductivity is 0.17 W/m.K. Continuity, momentum and by simplifying the energy equations and solving for each separately, a) The maximum temperature of the oil, b) Calculate the heat transfer rates to the bearing and shaft.
Harry up plz
question is image only part a
PLEASE ANSWER WITH DETAILED STEPS AND EXPLANATION. THANKS ?
A liquid is heated from 20 to 70 oC as it flows at 0.025 kg/s through a steel tube of 10 mm and 12m long. A uniform heat flux is maintained on the tube surface. Using the following liquid properties ρ = 1000 kg/m3, Cp = 4100 J/kg.K, k = 0.45 W/m.K, Pr = 10, μ = 2x10-3 kg/s.m. Calculate the average heat flux on the tube. Calculate the heat transfer coefficient at end of tube Calculate the surface temperature at exit and the heat transfer coefficient for first 1m of pipe?
Water flows at a rate of 0.8 kg /s in a 2.5 -cm diameter tube whose surface is maintained at a constant temperature of 90°C. If water must be heated from 35°C to 40°C, what is the value of the temperature on which you will base the value of the thermal conductivity that will be used to compute for the convection heat transfer coefficient? Express in Celsus.