Harry up plz Water (5.0 L/min) is flowing in a tube "D= 3 cm, L= 5 m" and is to be heated from15°C to 60.3°C by applying a uniformheat flux on the outer surface of the tubeby electric resistance heater. What is theconveçtive heat transfer coefficient(W/m .K)?If turbulent flow use Dituss-Boetler0.8relation Nu= 0.023 RePr .3Properties : p = 992.1 kg/m , C¸ = 4179J/kg.°C, k =,0.631 W/m°C, Pr ='4.32, v =0.658E-6 m /sSelect one:A. 726.36B. 876.33C. 837.79D. 799.25E. 760.71

Answered: Image /qna-images/answer/db28b34a-1817-4e54-9bd6-6e28ebccf84c.jpg

Water (5.0 L/min) is flowing in a tube “D = 3 cm, L= 5 m" and is to be heated from 15°C to 60.3°C by applying a uniform heat flux on the outer surface of the tube by electric resistance heater. What is the convective heat transfer coefficient

Water (5.0 L/min) is flowing in a tube “D = 3 cm, L= 5 m" and is to be heated from 15°C to 60.3°C by applying a uniform heat flux on the outer surface of the tube by electric resistance heater. What is the convective heat transfer coefficient

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: bäi The command using to insert :seal is

A: The Incident Command System is a standardized approach to the command, control, and coordination…

Q: 4 5/8" as meters

A: Given-4 5/8" or 4 5/8 inch To find-change the length into meter

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular…

A: Given: To find: Write a program to drill holes and mill

Q: draw the left side

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: Up milling operation is performed for finishing cut. Select one: True O False

A: Down milling is performed for finishing and get smooth surface.

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that , Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

Q: 9. To produce the line of intersection between the two cylinders, connect the project points using a…

A: Since we only solve up to three subparts, we will answer the first three. Please resubmit the…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

Q: find the requird fillet Size Ch) for figew soンル2 ん。レン46cm 26cm /2

A: Given data: - The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Identify the image shown below. O a. Taper shank O b. Drill chuck key O. Drift O d. Sleeve

A: Option C (DRIFT)

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear…

Q: Please show all work!! Figure is provided, work on a-c please.

A: a) Expression for Body Force Due to Rotational Acceleration The aircraft's propeller consists of a…

Q: Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS…

A: I have attached the image belowExplanation:

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: Shaper machine uses single point cutting tool for cutting mater Select one: True False

A: 1.true

Q: Identify the part not belonging to micrometer. Ratchet Clamp O Locknut Frame

A: Given :- Identity the part not belongung to micrometer Ratchet Clamp Locknut Frame

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: 1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three questions.…

Q: What is Line G?

A: Solution:

Q: In a tap set, an intermediate tap is used to start a thread form in a drilled hole Select one: O…

A: The given statement is true.

Q: The tool is shaper machine is fixed axis. O a. Z O b. A O c. Y O d. X

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Harry up plz

Water (5.0 L/min) is flowing in a tube "D
= 3 cm, L= 5 m" and is to be heated from
15°C to 60.3°C by applying a uniform
heat flux on the outer surface of the tube
by electric resistance heater. What is the
conveçtive heat transfer coefficient
(W/m .K)?
If turbulent flow use Dituss-Boetler
0.8
relation Nu= 0.023 Re
Pr .
3
Properties : p = 992.1 kg/m , C¸ = 4179
J/kg.°C, k =,0.631 W/m°C, Pr ='4.32, v =
0.658E-6 m /s
Select one:
A. 726.36
B. 876.33
C. 837.79
D. 799.25
E. 760.71

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw three views of the adjusting bracket. Drill-2 Holes Drill PROB. 20 Adjusting bracket.
What is the diameter of the groove?
Which of the following statement is correct in terms of degree of freedom? Select one: O Moving left and right is rolling O Moving up and down is surging O Swivels left and right is yawing O Moving forward and backward is heaving
perpendicular to the plane of the gear The side surface above the pitch cirnd de surface above thee pitch. known as Addendum a. Dedendum The flank of the tooth b. d. The face of the tooth
What is a Couple Moment?
Q6
What depth of cut is needed for a ¾ inch wide keyway in a 3 inches diameter shaft?
where does the 64 come from?
What size hole was drilled in part? Would it be 3/16?
Identify the operations from the figure re O Turning O Facing O Chamfering O drilling
A hole is to be drilled as shown by the circle. Using the part geometry shown below, indicate on the part sketch where locator(s) should be positioned according to the 3-2-1 principle. Use dashed lines to indicate locators on hidden surfaces. Also indicate where clamping force(s) should be applied using arrows. Use the minimum number of clamping forces.
Shaft G-Codes programming process (sumerik)