A solid piece of steel 60 mm in diameter and 80 mm height is reduced in height by 50 percent with the help of open die forging. The work material characteristics are represented by k = 350MPa and n = 0.16. If coefficient of friction is 0.1, find the maximum forging force. %3D

A solid piece of steel 60 mm in diameter and 80 mm height is reduced in height by 50 percent with the help of open die forging. The work material characteristics are represented by k = 350MPa and n = 0.16. If coefficient of friction is 0.1, find the maximum forging force. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: ' Explain briefly the relationship between the load-stroke in open die forging as illustrated in the…

A: Considering the open die forging:-

Q: c) A flat rolling operation is being carried out where the roll radius is 200 mm and the roll…

A: A rolling force is applied by rollers to the workpiece so as to reduce its thickness Maximum…

Q: Rolling: A rolling operation is performed on a 5 mm thick sheet of low carbon steel (K=530, n=0.26…

A: Given:To find:

Q: Please give me full explanation in 1hour do it fast A 4-in-thick aluminum slab is 10 in wide and 100…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: In a single diameter s and thickn of thickne

Q: Thickness of the plate is reduced from 40mm to 20mm by succesive cold rolling passes using identical…

Q: Figure 1. shows the rolling operation. Determine the position bn. of the neutral point? Neglect…

Q: 3. During the rolling process, the average flow stress is 20,000 lb/in², determining the amount of…

Q: 20. A forging process is shown at the figure below. Calculate the final diameter, if the initial…

Q: 1. Two thick slabs of 300mm each, the first one is used in cold rolling where u=0.08 while the…

A: Since we are allowed to answer one question at a time. We’ll answer the first question since the…

Q: A cylindrical part with 25 mm in diameter and 15 mm height is subjected to an open die forging…

A: Given data: Initial cylindrical diameter D=25 mm =0.025 m Initial height of cylinder hi=0.015 m Flow…

Q: 4- A round wire made of a 70-30 Brass (K=900 MPa, n=049 ) is being drawn a diameter of .08 in and…

Q: The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the…

A: The length of AB is written as, Free body diagram of the member BD with reaction and force…

Q: Drawing: A round rod of annealed 302 stainless steel (K = 1300 MPa and n = 0.3) is being drawn from…

A: Given:To find:

Q: Rod stock of initial diameter = 145 mm is drawn to the final diameter of= 120 mm. The draw die has…

A: given, Initial diameter , di = 145 mm Final diameter , df = 120 mm Die angle , α = 22 degrees.…

Q: A cylindrical working part is subjected to a forging landfall operation. The blank is 3.0 in. high…

A: volume of workpiece=π4×22×3=9.4247 in3

Q: A steel specimen of rectangular cross section with 120 mm width, 180 mm thickness and 90 mm height…

A: strain = -ln ( dh/hi) = - ln(35/90) = 0.94446 average flow stress flow stress = kεn1+n=1015…

Q: Estimate the power for annealed low carbon steel strip 200 mm wide and 10 mm thick, rolled to a…

A: Rolling is a metal forming process in which a material is plastically deformed by passing it between…

Q: 1. Two thick slabs of 300mm each, the first one is used in cold rolling where μ=0.08 while the…

Q: ndrical workpiece is forged in an open die. The workpiece The height after forging is 15 mm. The…

Q: A hot rolling operation is being carried out on 250 mm wide and 25mm thick low carbon steel…

A: Calculate the final thickness. hf=1-0.2ho =0.8×25 =20 mm Calculate the strain. Strain ε=lnhohf…

Q: process, a 150 mmx15 nd rotational speed is nis reduction is the m=

Q: What is the force needed to mechanically deform an aluminum bar with 50mm diameter? The yield and…

A: To find : what is the force need to mechanically deform an aluminum. Given : diameter D= 50 mm yield…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

A solid piece of steel 60 mm in diameter
and 80 mm height is reduced in height by
50 percent with the help of open die
forging. The work material characteristics
are represented by k = 350MPA and n =
0.16. If coefficient of friction is 0.1, find the
%3D
maximum forging force.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

* A cylindrical workpiece made of 1100-0 Aluminum that is 18 in high and 16 in in diameter and is to be reduced in height by 25% by open-die forging. Let the coefficient of friction be 0.15. K=20 mpa,n=0.35, Calculate the forging force.
Solve it
A wire is drawn through a draw die with an entry angle = 15o. The starting diameter is 0.100 in. And the final diameter = 0.080 in. The coefficient of friction at the work-given interface = 0.07. The metal has a coefficient of resistance K = 30,000 psi and a strain hardening exponent of n = 0.20. Determine the stretching force and the stretching force in this operation.
A compression test is performed on a 2” diameter by 5” long bar of an unknown metal. At the end of the compression test, the bar has a height of 3.5 inches. The strength coefficient (K) and the work hardening coefficient (n ) are 250 MPa and 0.4, respectively. State all assumptions needed to work the problem. a) Calculate the final diameter of the bar in inches. b) Calculate the flow stress in MPa when the length of the bar is 4”.
In a single pass rolling process using 410 mm diameter steel rollers, a strip width 140 mm and thickness 8 mm undergoes 10% reduction of thickness. Find the angle of bite in radians?
I need the answer as soon as possible
I am in a hurry, I need the answer as soon as possible, please help.
Q3) Explain briefly the relationship between the load-stroke in open die forging as illustrated in the figures bellow. Take in consideration the effect of coefficient of friction. 1500- 1000- 500 75 62 49 36 h (mm) 13 26 39 (h.-h) Stroke Forging force (1000 N)
None
A cylindrical 4135 cold-rolled steel workpiece has an upsetting load applied at room temperature using an open-die forging with flat dies to a new height, ha = 50 mm, as shown below. The initial diameter is do = 220 mm, the initial height is ho = 180 mm. 4135 cold-rolled MPa=1100 Psi= 16000 Strain hardening exponent, n = 0.14 A) What is the diameter of the forging at the end of the forging stroke? B) What is the longitudinal true strain of the forging at the end of the forging stroke? C) What is the true (flow) stress required in the material at the end of the forging stroke? D) Using the average pressure formula, what is the corresponding coefficient of friction if the upsetting force at the end of the stroke is 170 MN?
A upset forging operation is performed in an open die. The initial size of the workpart is: Do = 63 mm, and ho = 100 mm. The part is upset to a diameter = 70 mm. The work metal has a flow curve with strength coefficient = 600 MPa and strain hardening exponent= 0.22. Coefficient of friction at the die-work interface = 0.40. Determine (a) final height of the part, and (b) maximum force in the operation.
None