Q3/A/ a steel slab is upset forged from: (50mm×200mm×100mm) to (25mm × 200mm × 200mm). If the coefficient of friction between die and the material is 0.1 and K = 530 MPa, n = 0.26, find the forging force and pressure at x = 40 mm from center.imilcosm om Jell

Q: As a computer manufacturer, your goal is to provide high-quality computers with rapid processing…

A: we will dicuss on the beat way to build a low cost machine

Q: Instruction: Determine the moment of the force about point 0.

A: Given data as per question

Q: resolve, incorreect solutions

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: If the magnitude of the resultant force acting on the bracket is to be 550 N directed along the…

A: In basic terms, magnitude means 'distance or amount.' It depicts the absolute or relative size or…

Q: 5. A Pitot-static probe is used to measure the speed of an aircraft flying at 3000 m. If the…

A:

Q: what are the symbols for frictional force, applied force, normal force, and gravitational force?

A: ■ The frictional force exist due to surface roughness and the relative motion between the bodies. ■…

Q: would it be possible to get a detailed explanation? thank you

A:

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500 N load.…

A: Given data weight =500N Considering FBD of the system Considering vertical forces equlibirium…

Q: Problem 6: The top wall moves with velocity Vtop = 1" and the bottom wall is m S stationary. Inside…

A: VISCOSITY is defined as internal resistance offered by one layer of the fluid to the adjacent layer…

Q: any way the solution set c

A: Lead and aluminum both have FCC crystal structures  Density of solid aluminum= 2.71g/cm3.

Q: s Tafel p

A: introduction: here we have to explain tafel pot.

Q: The posltion of a particle is r = { (3t° - 2t)i - (4t"2 + t)j + (3ť° - 2)k} m, where t is in…

A: Given data  r = (3t2 - 2t) i - (4t1/2 + t) j + (3t2 - 2) k   To determine the magnitude of the…

Q: If cable AD is tightened by a turnbuckle and develops a tension of 1000 N, determine the tension…

A: Consider E is the origin. From the given diagram, the coordinates of A, B, C, and D are (0, 0, 30…

Q: : Determine the moment of the force about point A.

A: Given: TO determine: Moment about A

Q: Hello sir! Thank you for taking time to answer this question. I wonder if you could please write…

A:

Q: If 1 ton of bituminous coal is burned to generate electricity, how many kWh could be produced if the…

A: Dear student,                     There are two different problems that you have posted but…

Q: Please can you elaborate your answer? I do not understand. thank you

A:

Q: Thanks for your work. Can you please repost with pictures or any other way because my computer…

A: Mass m= 20 kg Damper coefficient C= 20 Ns/m Spring constant k= 4000 N/m Periodic harmonic force…

Q: The posltion of a particle is r = { (3t° - 2t)i - (4t"l2 + t)j + (3t² - 2)k} m, where t is in…

A: To determine the magnitude of velocity and acceleration of the particle.

Q: he several disadvantages as com

A: Answer given below.

Q: Determine the length b of the triangular load and its position a on the beam such that the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 1) Half-life of cessium-137 is 30.2 years. If the initial mass of a sample of cessium-137 is 1.000…

A: The half life is defined as the time required by a substance to decay to half of its Initial Value…

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: A family wishes to buy a 2020 Toyota Camry. The two options the consider are (a) a standard…

A: Given:Economy of SI engine, Vs=34 mpgFixed cost of SI engine, Fs=$18,000Economy of hybrid engine,…

Q: Does this example read true to yourself or is your way the correct way according to an external…

A:

Q: I want to know how to calculate how much paraffin wax is needed to give the required output force of…

A: Introduction: Paraffin wax: Paraffin wax is a white or colourless soft, solid wax. It's made up of…

Q: Choose a problem and apply the basic engineering process to solve it.

A:

Q: Explain in detail the Application of Physics (Electricity and Magnetism) in Engineering, especially…

A: The application of physics especially electricity and magnetism part in manufacturing are:-…

Q: Solve it all handwriting please

A: the stresses and select a shaft diameter for the industrial mixing machine. However, I cannot…

Q: a. Calculate the increase in rest mass of such a battery when it is taken from being fully depleted…

A:

Q: the use of machines

A: Belt Length At the point when the head and tail pulley are a similar size: L=(D+d)/2 x 3.1416+2CAt…

Q: The bracket is subjected to the two forces shown. Find the magnitude and coordinate direction angles…

A: Given F1 = 250 N F2 = 400 N To find Resultant  Direction of the resultant

Q: Good afternoon!  May I know where is the part of b) 4 mpa. Thank you!

A:

Q: An air hockey table has dimensions as shown in the picture. 0.3m Usually, the air from the table…

A: according to the given data

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.