A solid circular steel shaft AB, held rigidly at both ends, has two different diameters as in figure. Assuming that the maximum permissible shear stress is 80 MPa, determine the allowable torque T that may be applied at the junction C. Answer Tc ? N.m, 20 mm 40 mm B 0.2 m 0.5 m

A solid circular steel shaft AB, held rigidly at both ends, has two different diameters as in figure. Assuming that the maximum permissible shear stress is 80 MPa, determine the allowable torque T that may be applied at the junction C. Answer Tc ? N.m, 20 mm 40 mm B 0.2 m 0.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The copper pipe has an outer diameter of 2.5 in. and an inner diameter of 2.25 in. It is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown.(Figure 1) Points A and B lie on the pipe's outer surface. Figure C B |--M 2 ft V 150 lb-ft/ft. TIM A 2 ft V -- < 1 of 1 Determine the shear stress at point A. Express your answer to three significant figures and include appropriate units. TA = ΤΑ Submit Part B O — μA 4 TB = Value Units Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining μA P Determine the shear stress at point B. Express your answer to three significant figures and include appropriate units. Value Units ? www ? Submit Previous Answers Request Answer
Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as shown in Figure below, For steel has a 25 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 30 mm circular cross section, shearing modulus G - 28 GPa Determine: The two torques at supports A and C 2AN.m B. 3m 4m Steel aluninum Di-25mm Di-30mm G-83GPa G-28GP.
Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to the torques as shown in Figure Q2. Knowing that the entire shaft is made of aluminium for which G=27GPa, a. Determine the maximum shear stress and its location. Angle of twist at end D. b. EMU2113 Ø40 Ø30 Section p-p р A р 200 Section q-q 016 1500 Nm q 200 All dimensions in mm Figure Q2 Section r-r 500 Ø30 D 500 Nm
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A >50 kips 3 in 20 in 30 in
A 45-mm-diameter solid steel shaft supports loads PA = 1.1 kN and Pc = 2.2 kN as shown. Assume that L₁ = 155 mm, L₂ = 330 mm, and L3 = 240 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. A L₁ Answers: (a) Tmax= (b) max = i B L2 Pc MPa MPa L3 D
M (1) M 6 mm 2) P= 10 kN. The pin at point M has a radius R. If: 8 mm F.S.=2.5 a=250 mm & b=200 mm Angle between line of action of P and X-axis is 70⁰ Ultimate shearing stress at pin = 60 MPa Ultimate bearing stress at support posts= 150 Mpa Determine the minimum value of R 6 mm
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.46 GPa. For the steel segment BC, the diameter is 50 mm and G = 84.51 GPa. Given that a = 2.2 m and b = 1.35 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.01 MPa in the bronze and 83.59 MPa in the steel. Round off the final answer to two decimal places.
= 1.3-18 A stepped shaft ABC consisting of two solid，circular segments is subjected to uniformly distrib uted torque i，acting over segment 1 and concentrated torqueT₂applied at C，as shown in the figure。Seg ment 1 of the shaft has a diameter ofd₁= 57 mm and length ofL₁= 0.75 m; segment 2 has a diameterd₂= 44 mm and lengthL₂= 0.5 m。Torque intensity1₁3100 N m / m andT₂= 1100 N·m。（a）Find reaction torque T at support A.（b）Find the internal torque T（x）at two locations：
he compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.
Six 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel and six 20 mm diameter bolt in the inner bolt circle of 260 mm diameterare aluminum. What is the torque capacity of the coupling? Assume thatthe allowable shearing stress for the steel bolts is 40 Mpa and aluminumbolts of 30 Mpa. The Shear modulus of elasticity of aluminum and steel are28 Gpa and 84 Gpa, respectively.
The 45-mm solid shaft has an allowable shear stress of τallow= 65 MPa. The torsional loadings applied are shown in the figure provided. Determine the maximum torque of T1, as well as the maximum stresses within regions CD and DE