A solid circular shaft of uniform cross section is to be fixed at one end and free at the other end. It is to be subjected to a static torque of 877 N·m at its free end. The shaft material is selected to be a ductile material whose yield strengths in tension and compression are 410 MPa and 520 MPa, respectively. Using a factor of safety of 2.2, determine the required diameter of the shaft.

A solid circular shaft of uniform cross section is to be fixed at one end and free at the other end. It is to be subjected to a static torque of 877 N·m at its free end. The shaft material is selected to be a ductile material whose yield strengths in tension and compression are 410 MPa and 520 MPa, respectively. Using a factor of safety of 2.2, determine the required diameter of the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid circular shaft needs to be designed to transmit a torque of 50 N.m. If the allowable shear stress of the material is 140 MPa, assuming a factor of safety of 2, minimum allowable design diameter in mm is (a)8 (b) 16 (c) 24 (d) 34
Given: l1=1,3l; l2=1,9l; l3=1,2l; M1=-0,6M; M2=-1,6M; M3=1,9M. Parameter of length l=40cm; cross section diameters: d=41mm; d0=26mm. The shaft is made of steel with yielding shear stress τY=250MPa; factor of safety n=1,6. Find: the allowable value of load parameter (in Nm) MA = ?
shaft may be taken as 63 MPa. Assuming the weight of the shaft to be negligible in comparison with the other loads, determine its diameter. Take shock and fatigue factors for bending and torsion as 2 and 1.5 respectively. P = 20 kW = 20 × 103 W ; N = 150 rpm. ; T1/T2 = 2.5 ; WB = 900 N ; WA = 2700 N ; T = 63 MPa = 63 N/mm2 ; Km = 2 ; Kt = 1.5 ; DB = 750 mm or RB = 375 mm ; DA = 1250 mm or RA = 625 mm. A - Pulley A B в Gear 1250 D 750 750; 250 1000 350 1250- T2 T
0.6- 0.3 1.0 4.2 320 lb 1:25- 5.25 340 lb 2 1.0 1.95 0.3 B 0.6
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 3730 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.5-m length of shaft. 0.0807 rad 0.1091 rad 0.0556 rad 0.0861 rad 0.1009 rad
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
Question 3 The 80-mm diameter shaft, having an ultimate tensile and compressive strength of 80 MPa and 160 MPa respectively, is subjected to a combination of bending moment, M, of 15 kNm, an axial force, P, of 90 kN, and a torque, T, of 25 kNm as shown. Determine if the combined loading will cause any failure based on the Coulomb-Mohr theory. shaft M
A hollow steel shaft with an outside diameter of 41 mm and a wall thickness of 9 mm is subjected to a pure torque of T = 6300 N-m. The shear modulus of the steel is G = 87 GPa. Determine: (a) the maximum shear stress T in the shaft. (b) the magnitude of the angle of twist o in a 2.4-m length of shaft. Answers: (a) = i MPа. (b) p = i
Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb clockwise to 1000 in-lb counterclockwise as an applied bending moment at a critical section varies from + 4000 in-lb to 2000 in-lb. The shaft is of uniform cross section and no keyway is present at the critical sec- tion. Determine the required shaft diameter. The material has an ultimate strength of 80,000 psi and a yield strength of 60,000 psi. Base design on a factor of safety N=1.5. Take the endurance limit as half the ultimate strength.
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?
A solid shaft made from AISI 1040 cold-drawn steel is used to carry two V-belt, as shown in the Fig. 3. Pulley A receives power from a motor through a belt, with the belt tensions shown in Fig. 3. The power is transmitted through the shaft and delivered to the belt through pulley B. Assume the belt tension on the loose side is 10 percent of the tension on the tight side.
You are designing a driveshaft for a motor from a material with G = 15,000 ksi. The specifications for the project require a solid shaft to be used. Based on the location of the motor, the driveshaft has a length L = 9.55 ft. The motor provides 67 hp at a rotation rate of 2475 rpm.Your design requires φ ≤ 0.905° over the length of the shaft. Additionally, the maximum shear stress in the material τmax ≤ 4.0 ksi.Determine rmin, the minimum radius