shaft may be taken as 63 MPa. Assuming the weight of the shaft to be negligible in comparison with the other loads, determine its diameter. Take shock and fatigue factors for bending and torsion as 2 and 1.5 respectively. P = 20 kW = 20 x 103 W ; N = 150 rpm. ; T1/T2 = 2.5 ; WB = 900 N ; WA = 2700 N ; T = 63 MPa = 63 N/mm2 ; Km = 2; Kt = 1.5 ; DB = 750 mm or RB = 375 mm ; DA = 1250 mm or RA = 625 mm. A - Pulley A B. B Gear 1250 D 750 750; 250 1000 350 1250-

shaft may be taken as 63 MPa. Assuming the weight of the shaft to be negligible in comparison with the other loads, determine its diameter. Take shock and fatigue factors for bending and torsion as 2 and 1.5 respectively. P = 20 kW = 20 x 103 W ; N = 150 rpm. ; T1/T2 = 2.5 ; WB = 900 N ; WA = 2700 N ; T = 63 MPa = 63 N/mm2 ; Km = 2; Kt = 1.5 ; DB = 750 mm or RB = 375 mm ; DA = 1250 mm or RA = 625 mm. A - Pulley A B. B Gear 1250 D 750 750; 250 1000 350 1250-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dont ask for Material property. This is the only data provided. Dont keep asking for material property.
Q8
т M1 M2 L1 L2 Two parts shaft of lengths L, = 2.5 m, L,=2.0 mis loaded by two concentrated moments M, = 5 kNm, M,=6 kNm and the distributed moment of the intensity m = 2 kNm/m Define the torque in the cross-section of shaft z = 3 m. Note: The torque is accepte as positive, if looking at the shaft section plane from outside , the moment actoin can be seen in the counter-clockwise direction
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
5 - A thin-walled pressure vessel is subjected to internal pressure p 1 MPa. What is the maximum allowable torque T, applied along the longitudinal axis, if the maximum allowable tensile stress is 80 MPa? ↓t=3mm 240mm polar moment of inertia J=2r³t
at question A=110 MPa B=-60 MPa M=145N.m
P9-1 a thanks
You are designing a driveshaft for a motor from a material with G = 15,000 ksi. The specifications for the project require a solid shaft to be used. Based on the location of the motor, the driveshaft has a length L = 9.55 ft. The motor provides 67 hp at a rotation rate of 2475 rpm.Your design requires φ ≤ 0.905° over the length of the shaft. Additionally, the maximum shear stress in the material τmax ≤ 4.0 ksi.Determine rmin, the minimum radius
The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the gear on the shaft is 0.9 kg, dimension, surface and notch factors KbK / Kç = 0.83, shaft speed n = 1120 rpm, shaft transmitted power 7.5 kW, force on shaft Fn = F = 2680 N Since the desired safety coefficient is Ssafe = 2; Check the safety of the shaft