A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing machine until the applied torque reaches the value T = 500 N · m. At this value of torque, a strain gage oriented at 45° to the axis of the bar gives a reading e = 339 x 10-6. What is the shear modulus G of the material? Strain gage d = 50 mm T= 500 N-m Round to one decimal place. G = GPa

A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing machine until the applied torque reaches the value T = 500 N · m. At this value of torque, a strain gage oriented at 45° to the axis of the bar gives a reading e = 339 x 10-6. What is the shear modulus G of the material? Strain gage d = 50 mm T= 500 N-m Round to one decimal place. G = GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 70 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 60 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 170 kN, determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, E = 100 GN/m2.
The polymer bar shown in the figure below has a width of b = 59 mm, a depth of d = 90 mm, and a height of h = 258 mm. At a compressive load of P = 120 kN, the bar height contracts by Ah = -2.40 mm, and the bar depth elongates by Ad = 0.37 mm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b. P Rigid plate (a) E = i (b) v = (c) Δb = i i GPa mm b h Rigid base
10.Stress transformation. From the figure below, find the orientation of the maximum principal stresses, the magnitudes of the maximum principal stresses and the maximum shear stress. All formulae given at the end of the exam. 2/22 27200005 27200032 10 MPa 40 MPa 50 MPa
PROBLEMS 203. During a stress-strain test, the unit deformation at a stress of 5000 psi Wap ODserved to be 0.000167 in./in. and at a stress of 20,000 psi it was 0.000667 in./in. If the proportional limit is 30,000 psi, what is the modulus of elasticity? What is the stress corresponding to a strain of 0.0002 in./in.? Would these re- sults be valid if the proportional limit were 18,000 psi? Explain. E = 30 X 106 psi; S 6000 psi %3D Ans. 204. A uniform bar of length L, cross-sectional area A, and weight W is sus- WL If pended vertically from one end. Show that its total elongation is & = 2AE wL? its weight per unit volume is w, show also that & 2E A steel rod having a cross-sectional area of sq in. and a length of 600 ft is suspended vertically. It supports a load of 5000 lb at the lower end. If steel 30 X 106 psi, find the total elongation in the rod. Ans. 8 = 2.64 in. 205 weighs 490 lb/cu ft and E Hint: Use the result of Prob. 204. steel wire 30 ft long, hanging vertically, supports a…
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
Given an element with stresses as indicated in the figure, answer the following questions. (1) The major and minor principal stresses and the planes on which they act. (2) The max. shear stress and the inclination of the plane on which it acts.
Last digit of my id is 0
1. If we take the stress function = 2x²y + xy², what are the stress components according to this stress function? What are the stresses on the boundaries of the body below? O y H H L X
333. two decimal places
Must solve the entire question. Dont solve partially.
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
A rigid slab weighing 600 ku is placed upon two ·bronze rods and one steel rod each of 6000 mm² area at a temperature of 15¢ as shown, find the temperature at which the stress in steel rod will be Zero? take: Coefficient of expansion for steel = 12 um/m. c coefficient of expansion for bronze = 18 um/m. c Young's modulus for steel = 200 G Va Young's modulus for bronze = 80 GPa 600 IN 250mm 300mm -bronze -Steel