Show that the strain rate of a wire stretching through a die can be expressed by e=2tg(a)/r *(dx /dt) What is the maximum strain rate for 0.040 in. diameter wire is pulled at 2000 ft/min through a die with a half angle of 10⁰? Demuéstrese que la velocidad de deformación de un alambre que 2 tg a dx estira a través de una matriz puede expresarse por é=- ¿Cuál es la " dt máxima velocidad de deformación para alambre de 0,040 pulg de diámetro es tirado a 2000 pies/min a través de una matriz con un semiángulo de 10°?

Show that the strain rate of a wire stretching through a die can be expressed by e=2tg(a)/r *(dx /dt) What is the maximum strain rate for 0.040 in. diameter wire is pulled at 2000 ft/min through a die with a half angle of 10⁰? Demuéstrese que la velocidad de deformación de un alambre que 2 tg a dx estira a través de una matriz puede expresarse por é=- ¿Cuál es la " dt máxima velocidad de deformación para alambre de 0,040 pulg de diámetro es tirado a 2000 pies/min a través de una matriz con un semiángulo de 10°?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What are the internal forces at point C of the beam
Find the solution of the differential equation d = 2* A. y = x B. y=x²-x* C. y = √x8x4 D. y = x - 1 E. Not in the list. Select one: O a. b O b. d O c. a d. e O e.c Clear my choice
4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small roadway. The beam is used on a 30 ft simple span, and the total factored load including the beam's self-weight is 15.6 kips/ft. Assume d = 21" for your calculations. fc' = 6000 psi and fy = 60000 psi. a. Calculate the maximum mid-span moment - this is Mu b. Check the effective width of the beam as per ACI 318-19 Table 6.3.2.1 C. Check whether the T-Beam designed as a rectangular section would be able to provide the required Mu. If not, design the section as a T-Beam to calculate the required reinforcement. Try to keep close to 0.9 (it is okay if it's a little under). But calculate the correct value of . d. Sketch the section following the guidelines for bar arrangement.
Y Given: X x1 x2 . x1 = 15.35 mm • x2 = 16.74 mm . x3 = 16.10 mm .y1 = 19.32 mm y2 = 20.55 mm y3 = 16.37 mm mie x3 sterren T y3 y2 y1 Find x & y centroid
I5KN Draw and label the V and M diagrams. Fill in the blanks. Find M- max and the equations for q, V, and M in the region 3
pls replyy asap!! Determine the location of the horizontal neutral axis of the section (in mm) with respect to the bottommost fiber, All dimensions are in mm.
Which among the following determines the direction of closing error? a. Tanō = [D/EL O b. Tanō = [L/ED c. Tan ō = [L²/ED² d. Tan ō = [D²/>L²
17- O A) Omm B) 15 mm O 9 40 mm O D) 7.5 mm O E) 30 mm
What do you mean by intergranular?
Q1/1/2/if C(5*5) the counter of the rows is i and the counter of the columns isj,what is the relationship between thesetwo countersfor the elements that located under the main diagonal elements of matrix C. 1. 12] 2. isj 3. i
Someone can help me with these, I'm stock?
Cross-Section A (Channel Cross-Section) The first cross-section is what is often referred to as an open 'channel' cross-section. The dimensions are given as: b = 160 mm ● ● ● d = 220 mm t = 40 mm ● • x b With reference to the origin shown above, what are the coordinates of the centroid for this cross-section: y - X -t- Imax • Imin mm mm d What is the maximum and minimum second moment of area about axes passing through the centroid: mm4 mm 4