17-O A) OmmB) 15 mmO 9 40 mmO D) 7.5 mmO E) 30 mm A rack is made from roll-formed sheet steel and has thecross section shown. Determine the location (x, y) of thecentroid of the cross section. The dimensions are indicatedat the center thickness of each segment.y-30 mm-54380 mm50 mm21715 mm15 mm15* x +50* x, +15*x3 +30 * x, +30 *x5 +80* x6+15 *x,X =Σ235X4 = ?%3D

Given:- A rack is made from roll-formed steel sheet To determine:- The value of x4 The location of…

A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location (x, ỹ) of the centroid of the cross section. The dimensions are indicated at the center thickness of each segment. -30 mm- 5 4 80 mm 50 mm 2 7 15 mm 15 mm 2*L 15* x, +50*x, +15* x, + 30 * x, + 30 *x, +80*x6 +15 *x Σ x = 235 x4 = ? 3.

A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location (x, ỹ) of the centroid of the cross section. The dimensions are indicated at the center thickness of each segment. -30 mm- 5 4 80 mm 50 mm 2 7 15 mm 15 mm 2L 15 x, +50x, +15 x, + 30 * x, + 30 x, +80x6 +15 *x Σ x = 235 x4 = ? 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. 50, 100 100 99.45 T- 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa a. Determine the design strength due to yielding in the gross section. (kN) b. Determine the allowable strength due to yielding in the gross section. (kN) c. Determine the design strength due to fracture in the net section. Use U = 0.85. (kN)
07
A steel plate (called a cover plate) having cross-sectional dimensions 5.6 in. x 0.48 in. is welded along the full length of the bottom flange of a W 12 x 50 wide-flange beam (see figure, which shows the beam cross section I W 12 × 50 5.6 x 0.48 in. cover plate O What is the percent increase in the section modulus (as compared to the wide-flange beam alone)? (Assume bending around the horizontal centroidal axis.)
Hand written please
complete solution and drawing.If u can pls include some explanation, thankyou!
Question 4 Complete the table below for the steel sections shown. All sections are bending about their horizontal axis. Section Location hep Ney Slenderness (show calculations) of element bf Flange te ld ++ tw be = 800 mm Web tf = 20 mm d = 1440 mm tw = 16 mm Grade 300, heavily 入。= Whole Asp= Asy= welded plates section br Flange tr d Web bf = 800 mm te = 20 mm d = 1420 mm tw = 16 mm Grade 300, heavily welded plates 入。= Whole Asp= Asy= section
Bolted and Riveted Connections From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm bigger than the bolt, the angular section is 100 x 75 x 8 mm, with an area of 1340 mm2. Thickness of the gusset plate is 9mm. The gusset plate and angle arc A36 steel with Fy = 250 MPa and Fu = 400 MPa. Determine the tensile capacity of the connection based on gross area. Determine the tensile capacity of the connection based on effective net area using a reduction factor of 0.85. Determine the tensile capacity of the connection based on gross area.
Calculate the service tensile load capacity for an angle bar L 125 x 75 x 12 A53 steel connected with 13 A490 bolts as shown in the Figure 2. Diameter of holes is 3mm larger than the bolt diameter. Bolt diameter = 13 mm Standard hole = 24 mm Use hole diameter = 13 + 3 = 16 mm a = 43.5 mm b = 51 mm c = 36 mm d = 252 mm
An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. %3D 50, 100 100 99.45 T- 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm? y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the design strength due to fracture in the net section. UseU 0.85. (kN)
Beam description (repeated): A simply supported beam with a T-shaped section is being designed, as shown in the figure below. The beam has overall dimensions of 900 mm wide top flange, 750 mm deep, and a web thickness of 400mm and flange thickness of 150 mm. A total of 7-HD25 longitudinal reinforcing bars are located in the bottom of the beam, 4-HD25 bars at the top, and 8 - HD16 in the flange. The concrete strength is f'c = 30 MPa. The depth to the centre of the bar group at the bottom of the beam is 675mm. Question: Assuming nominal shear reinforcement is provided, calculate the concrete contribution to the shear strength (Vc). Give your answer below in kN.
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Р, 3 500 k PL = 1,000 k 500 k PD 1,000 k |fixed fixed Check whether a 17 ft W 14 x 211 section of A992 steel can safely carry the given applied service loads pinned 35 ft 18 ft \pinned pinned Strong Axis Weak Axis