A slab of stone of area (3600 + R) cm² and thickness 10 cm is exposed on the lower surface to steam of (100 + R)° C. A block of ice at 0° C rests on upper surface of the slab. In one hour 4.8 kg of ice is melted. Calculate the thermal conductivity of the stone. Consider the specific latent heat of ice is (3.36 + R) x10° Joules. R=76

A slab of stone of area (3600 + R) cm² and thickness 10 cm is exposed on the lower surface to steam of (100 + R)° C. A block of ice at 0° C rests on upper surface of the slab. In one hour 4.8 kg of ice is melted. Calculate the thermal conductivity of the stone. Consider the specific latent heat of ice is (3.36 + R) x10° Joules. R=76

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please answer asap
Measuring the temperature of very cold substances can be challenging. Here is one way of measuring the temperature of liquid nitrogen. A 50g flake of aluminum is submerged in liquid nitrogen and left immersed until it is in thermal equilibrium. The flake is then removed and placed in a well-insulated container with 500ml of water at 30°C. When water and flake attain thermal equilibrium, the temperature of the water is found to be 25°C. What was the temperature of the liquid nitrogen?
2 (a) The inner and outer surfaces of a 5m x 10m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m·K are maintained at temperatures of 20°C and 5°C, respectively. (i) Determine the rate of heat transfer through the wall, in W. [Note: State all assumptions] (ii) Explain the effect of thermal conductivity in rate of heat transfer
Will definitely upvote
3. A well-mixed cement-lined storage tank contains water initially at 50°C. The water loses energy to its surroundings via conduction through the tank's concrete-lined walls. The tank sits in an unheated warehouse with an air temperature of 0°C. A diagram of the storage tank is shown below. The cement lining is 1.5-cm thick and has a thermal conductivity (htc) of 2.0 W/(m K). height = 1.5 m diameter = 2.0 m a. How long will it take (in minutes) for the water to cool to 40°C? b. Why might you be over- or underestimating the time it will take to cool the contents of the reactor?
Q2: A long 25 cm diameter cylindrical shaft made of stainless steel 304 comes out of an oven at a uniform temperature of 500 •C. The shaft is then allowed to cool slowly in an environment chamber at 180 °C with an average heat transfer coefficient of h=90 W/m2. °C. Determine the temperature at the center of the shaft 40 min after the start of the cooling process. Also, determine the heat transfer per unit length of the shaft during this time period. Taking p=7900 kg/m3, * .Cp%3477 J/kg. •C, k= 14.9
Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285 K and hot reservoir at 350 K. It is also equipped with a metal can cylinder that has a volume of 0.0002 m3. How many moles of air are present in the system if the metal cylinder is in the cold tank and the measured pressure and the total air volume are 104160 and 0.00015 m3, respectively?
A 0.025-mm-diameter stainless steel wire having K =16 W/m • C is connected to two electrodes. The length of the wire is 80 cm and it is exposed to a convection environment at 20 •C with h = 500 W/m2 • •C. A voltage is impressed on the wire that produces temperatures at each electrode of 200 -C. Determine the total heat lost by the wire in cal/hr.
At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
A 6-pack canned drink is to be cooled from 25°C to 3°C. The mass of each canned drink is 0.355 kg. The drinks can be treated as water, and the energy stored in the aluminium can itself is negligible. Solve for the amount of heat transfer from the 6 canned drinks.
A plane wall 3.5 cm thick generates heat internally. The wall is made of a material with thermal conductivity of 44 W/m K. Both faces of the wall are maintained at 50.30°C. If the maximum temperature inside the wall is 61°C, what is the rate of internal heat generation in the wall per unit volume? Express your answer in W/m³.
The convection coefficient for a hot a fluid flowing over a cool surface is 150 W/m^2. The fluid temperature is 410 K and the surface is held at 290 K. Determine the heat transfer per unit surface area from the fluid to the surface.