H.W. Q: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom with diameter 20 cm and thickness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan. 105°C 0.4 cm Answer: T= 105.43 °C 800 W

H.W. Q: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom with diameter 20 cm and thickness 0.4 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 800 W. If the inner surface of the bottom of the pan is at 105°C, determine the temperature of the outer surface of the bottom of the pan. 105°C 0.4 cm Answer: T= 105.43 °C 800 W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamics
Question 4 The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4 W/m-K. A heater is used to maintain the room temperature at 22 °C. Take the convection heat transfer coefficients on the outer surface of the window to be 12 W/m²-K. Take appropriate assumptions while solving this problem. (a) T₁-15°C TA -A=1m x 3m 3m², k=1.4 W/m-K I L=0.005m Figure Q2 ** -T₂=5°C Find the convection heat transfer coefficients on the inner surface of the window.
Q2: A long 25 cm diameter cylindrical shaft made of stainless steel 304 comes out of an oven at a uniform temperature of 500 •C. The shaft is then allowed to cool slowly in an environment chamber at 180 °C with an average heat transfer coefficient of h=90 W/m2. °C. Determine the temperature at the center of the shaft 40 min after the start of the cooling process. Also, determine the heat transfer per unit length of the shaft during this time period. Taking p=7900 kg/m3, * .Cp%3477 J/kg. •C, k= 14.9
A spherical container, with an inner radius r1= 1.4 m and an outer radius r2 = 1.45 m has its inner surface subjected to a uniform heat flux of q1= 7 kW/m2. The outer surface of the container has a temperature T2 = 25°C, and the container wall thermal conductivity is k = 1.5 W/m∙K. Determine the inner surface temperature of the container. (Round your answer to the nearest whole number.) The inner surface temperature is ____°C.
Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 40 W/m-K and a thickness L = 0.3 m, with no internal heat generation. -T2 L Determine the heat flux, in kW/m², and the unknown quantity for each case. Case T1(°C) T2(°C) dT/dx(K/m) q (kW/m?) 1 50 -20 i i 2 -30 -10 i i 3 70 i 160 i 4 i 40 -80 i 5 i 30 200 i
H.W1 Consider a person standing in a room. Determine the total rate of heat transfer from this person if the exposed surface area and temperature are 1.6m² and 29°C, respectively. Assume that the convection heat transfer coefficient is 6W/m².K and the emissivity of a person is 0.95. The air temperature in the room is maintained at 22°C at all times of the year. In summer, the wall and ceiling temperatures are observed to be 25°C, while in winter, they are 10°C. Ans: Qrotal =104.4 W In Summer Qrotal =231.3 W In Winter
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m.K) or copper (k = 390 W/m-K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials? Aluminum: T = i °℃ Copper: T = °℃ i
1- Microwave radiation is incident on one side of a planar wall with a heat conductivity coefficient k. (x=0) -D°b=(x)b leads to volumetric heating. While this surface is 9(W/m²) microwave radiation is fixed. kept at a constant temperature To, the other surface at x=L is very well insulated. Determine the temperature distribution T(x) in terms of x, L, k, qo and To.
asap
A house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.
The temperature of a gas stream is measured by a thermocouple whose junction can be approximated as a 1-mm-diameter sphere. Take the junction’s properties as: k of 32 W/m K, density of 8.2 kg/m^3, c of 300 J/Kg K. On its surface, the overall heat transfer coefficient is 200 W/m^2 K. Neglect any conduction loss from the sphere to other parts of the thermocouple. Create a plot of measurement error as a function of time for the thermocouple, expressed as a fraction of the initial temperature difference.