A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q=0.265 m^3/s, a water density p = 1.000 x 103 kg/m^3, a rotation speed n = 2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Looking at the following image, find all values of the velocity triangle just before the impeller inlet and just after the impeller outlet at radius r =0.09 m. impeller Figure 37.1 A propeller of an axial flow pump U₁ Outlet guide vane B₁ Impeller a₂ U₂=U₂=U

A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given. At a radius of r =0.090 m, absolute flow flows in from the axial direction just before the impeller inlet and relative flow flows out in the axial direction just after the impeller outlet. Assuming a flow rate Q=0.265 m^3/s, a water density p = 1.000 x 103 kg/m^3, a rotation speed n = 2.4 x 10^3 rpm, and a gravitational acceleration g = 9.81 m/s^2, and assuming that the theoretical head Hth = W/g (W: specific work) derived from Euler's law is constant at all impeller radii, answer the following questions. (1) Looking at the following image, find all values of the velocity triangle just before the impeller inlet and just after the impeller outlet at radius r =0.09 m. impeller Figure 37.1 A propeller of an axial flow pump U₁ Outlet guide vane B₁ Impeller a₂ U₂=U₂=U

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm, L= 50m, = 0.02, minor loss is neglected. The pump performance curve is approximated by the equation: H,=21.5-6507 Where H, is in meters and Q is in m/s. Determine the discharge O and pump head /7 when two pumps in series are used for total static head (4Z=25m).
Given parameters D1=30 cm L1=300 m D2=20 cm L2=150 m D3=25 cm L3=200 m f1=0.018, f2=0.02, and f3=0.019, determine the flow rate between reservoirs A and B, which are connected to each other as shown in the diagram. Note that the sudden contraction loss coefficient k is assumed to be 0.24.
Problem 5.2 A simple air duct with a side exhaust is shown below along with the direction of the velocity vectors at each inlet or outlet. The cross-sectional area at 1 and 3 are identical, Ac1 = Ac3 = 0.5 m². The velocity at 2, V₂, makes a 20° angle with the opening in the side of the duct A₂ = 0.5 m². Measurements indicate that the flow is steady with velocities V₁ = 10 m/s and V3 = 3 m/s. Assume that air behaves like an incompressible substance under these conditions. a) Determine the ratio of the volumetric flow rate at 2 to the volumetric flow rate at 1, /. b) Determine the ratio of the velocity at 2 to the velocity at 1, V₂/V₁. 1 20° Ans: a) 0.65 ≤ / ≤ 0.81 b) 1.75 ≤ V₂/V₁₂ ≤ 2.10
Two identical centrifugal pumps connected in series are used to pump water between two storage tanks that are open to the atmosphere, through a cylindrical pipe with ID of 0.1 m on both the discharge and suction side. The total equivalent length on the suction and discharge sides are 20m and 40m respectively. The change in static head is 7m. Pump Data: Q( m3/s) 0 0.01 0.02 0.03 0.04 Δh (m) 23 21.5 18.5 11 3 Assume the friction factor f to be 0.02 and is constant throughout the range of flowrates. a) Determine the operating point of the system. b) Determine the power requirement for the pumping system if the pump efficiency is 75%.
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
Q3.A Francis turbine has the dimensions of r=1.42 m, r,=2.00 m br=2.20 m and by=0.731m. Rotation speed of the turbine is 180 rpm. Three angles of velocities at the inlet and outled of the blade are defined as oaz= 35° and al=25° The flow rate of turbine is 340 m/s and the total head of the turbine is 80 m. Neglecting losses, www a) Draw the velocity three anges at inlet and outlet of the blade. b) Calculate blade angles at inlet and outlet of the blade, Power. Net head of turbine. c) Losses in water channel (Penstock). Note: Point (2) presents inlet and while point (1) presents outlet section of blade. Adjustable guide vane Blade n
As discussed in class, rotor wheel turbines are commonly used in hydroelectric power plants to generate electric power. In the Pelton wheel design below with radius r = 2 m, a high speed water jet (with Vj = 50 m/s and flow rate 10 m3 /s) impinges on buckets making an angle β=160 degrees, forcing the wheel to rotate at constant angular speed ω = 150 revolutions per minute. Calculate the power delivered to the rotor if there are 10 jets as described above surrounding the Pelon wheel.
A and B are homologous pumps operating at the speed of 800rpm.Pump A has an impeller with diameter 60 cm and discharges 1.5m^3/s of water under a net head of 60m.Calculate the size of pump B, net head and the specific speed to discharge 0.9m^3/s.
Water from a large reservoir drives a turbine, and exits as a free jet from a pipe of diameter D. The jet is deflected by a vane, and the horizontal force required to hold the vane is F directed to the left. Given: h = 40m, D = 0.15m, 0 = 30°, F, = 1500N, and Pw = 1000 kg/m³. Assume velocity magnitude at exit of vane is equal to that at entrance. If all losses are negligible, calculate: (a) The power developed by the turbine in kW. (b) The pressure difference across the turbine, and express it as a head (m). h Figure 1: Problem 2, A sketch (not-to-scale) Equations used must be labeled appropriately: conservation of mass, principle of linear momentum, principle of angular momentum, or first law of thermodynamics. Control volumes must be drown and clearly defined. List all assumptions.
Problem 2. An engineer helps with the design of a rotating spray for a dishwasher. The spray has 4 identical jets spaced equally around the rim of a disc. Water enters though a hollow shaft and then flows radially out to the jets. The nozzle of the jet has a diameter D of 0.3 cm and makes an angle a = I (3 with the horizontal plane of the disc(See figure). The jets are oriented so that v2r=0. If the total flowrate Q=50 mL/s and the disc has radius R= 7.5 cm, determine the torque in dyne-cm required to keep the disc from rotating. Water jet R. Water flows radially inside dise to jet Water in View from top View from side
Two pumps (Pump A and B) have performance curves which can be approximated by the following equations: H_A = 340 - (1.2(Q^2)), in feet H_B = 360 - (2.5(Q^2)), in feet where Q is in ft^3/s. If pumps A and B were to operate in parallel as depicted in the figure below, at what head (in ft.) should either pump be operated?
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height at the impeller outlet b2 = 0.02 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.3 m³/s. The outlet blade angle 3₂ = 31 degrees and the impeller rotational speed w = 1400 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The impeller power is ß₂ kW. Front View ra @ b2- → Side View