A single reduction gear of 120 kW with a pinion 250 mm pitch circle diameter and speed 650 r.p.m. is supported in bearings on either side. Calculate the total load due to the power transmitted, the pressure angle being 25°. then calculate the total load when the speed be 1300 r.p.m to transmit 250 kW of power.

A single reduction gear of 120 kW with a pinion 250 mm pitch circle diameter and speed 650 r.p.m. is supported in bearings on either side. Calculate the total load due to the power transmitted, the pressure angle being 25°. then calculate the total load when the speed be 1300 r.p.m to transmit 250 kW of power.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A walkway suspended across a hotel lobby is supported at numerous points along its edges by a vertical cable above each point and a vertical column underneath. The steel cable is 1.27 cm in diameter and is 5.45 m long before loading. The aluminum column is a hollow cylinder with an inside diameter of 16.14 cm, an outside diameter of 16.24 cm, and unloaded length of 3.25 m. When the walkway exerts a load force of 8,400 N on one of the support points, how much does the point move down? mm
A 4.5 long iron rod with a cross-sectional area of 0.75 centimeter square stretches 0.85 mm when a mass of 195 kg hung from its lower end. Compute the Young's modulus in GPa for the iron rod.
An airplane flies at 300 km/h at sea level at 20°C. The propeller diameter is 1.8 m, and the velocity of the air through the propeller is 360 km/hr. Find: ( a) The slipstream velocity relative to the airplane. (b) The thrust. (c) The power input. (d) The power output. (e) The efficiency. (f) The pressure difference across the propeller disk.
Q1 show thot the force F-jz_6xŻ)I+ (2x9Z); ij+(3x4z-67)is cors exvative, hence find i the Patenial fun Ction.
4. A single axial load of P = 60 kN is attached at the end C of the brass rod ABC. Knowing that E = 105 GPa, determine the diameter d of the portion BC for which the deflection of point C will be 3 mm. 30 mm d 1.2 m B P 10.8 m
1. A propeller 1 f t in diameter rotates at 1200 rpm in water and absorbs 2 hp. Find the power coefficient, and estimate the power required to increase the speed to 1500 rpm if the power coefficient remains constant. 2. A high-speed two-bladed wind turbine 35 m in diameter operates at its peak effi- ciency in winds of 30 km/hr. Estimate the power generated, the rotor speed, and the wind velocity in the wake.
The steel band shown is 50 mm wide and is secured around the smooth rigid cylinder. If the bolts are tightened so that the tension in them is 1800 N, find the normal stress in the band, the pressure exerted on the cylinder and the distance half the band stretches. Assume E = 200 GPa.
The spiral grooves are cut in the barrels of the guns and rifles. Explain why?
Q6/ A V-belt having a lap angle of 180° have a cross sectional area of 6.2 cm2 and runs in a groove of inclined angle of 40°. The density of belt is 0.0013 kg/cm and maximum stress is limited to 400 N/cm2 and u = 0.2. Find the maximum power that can be transmitted, if the pulley has mean diameter of 30 cm and runs at 1000 rpm.
A load of 2 kg produces an extension of 1 mm in a wire 3 m long and 0.1 cm in diameter. Find Y of the wire.
None
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 1 m depth. a.17.8 b.63.0 c.393.9 d.3.9