3 mm 200 mm
Q: The velocity distribution for the flow of oil (SAE 10W) at 38°C between two walls is given by V =…
A: V=100y0.1-y Shear stress is a type of stress that arises when a force is applied parallel to a…
Q: For a one-component system under conditions of constant pressure, how many phases can normally be at…
A: Given: The number of components of the system is C = 1
Q: f a compressional stress of 200.0 N is applied to a copper rod having a diameter of .500 cm and a…
A:
Q: nd trim printed circuit sheets. For the position shown, determine the vertical component of the…
A: Px = 390 sin 13 = 87.73 NPy =390 cos 13 = 380 N(FBD)x =2510034 FBD(FBD)y =9710034FBD
Q: Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial…
A: Initial volume (V) = 1.28×10-6 m3 Pressure or Stress (P) = 5.05 GPa or 5.05×109 Pa Bulk Modulus (B)…
Q: A 8-mm-thick rectangular alloy bar is subjected to a tensile load P by pins at A and B, as shown in…
A:
Q: A 3.7-carat diamond is grown under a high pressure of 58x109 N/m2. One carat is 0.200 g, and you can…
A: The volume change of a 3.7-carat spherical diamond when withdrawn from the chamber and exposed to…
Q: At the proportional limit, a 49 mm wide by 13 mm thick bar elongates 2.7 mm under an axial load of…
A: Given: Here are the given data, Width=49 mm Thickness=13 mm…
Q: a)What is the magnitude of the bone shear force acting on the vertebra?Report in N b)what is the…
A: The objective of the question is to calculate the magnitude of the bone shear force and the bone…
Q: 7.24 For this system, the discharge of water is 0.1 m³/ x = 1.0 m, y = 2.0 m, z = 7.0 m, and the…
A: As a result, Bernoulli's theorem indicates that a decrease in fluid pressure means an increase in…
Q: A 350 mm diameter solid steel drive shaft transmits 4500 kW at 120 rpm to a hollow steel shaft via a…
A: Given,Drive shaft diameter (D) = 350 mm Transmitted power (P) = 4500 kW Rotational speed (N) = 120…
Q: Consider a metal bar of length L, cross-sectional area A, and Young's modulus Y. When a tension…
A:
Q: A stainless steel tube with an outside diameter of 46 mm and a wall thickness of 5 mm is used as a…
A:
Q: 4. A single axial load of P = 60 kN is attached at the end C of the brass rod ABC. Knowing that E =…
A:


Step by step
Solved in 2 steps

- Member BC has a square cross section. The diameter of the pins at A and B are 3 cm and 2 cm respectively. If the allowable normal stress for member BC is allow = 25 MPa and the allowable shear stress for the pins iS Tallow = 12 MPa, calculate the maximum force intensity w (in N/m). 4 cm В 50° 3 m A WArtificial diamonds can be made using high- pressure, high-temperature presses. Suppose an -6' artificial diamond of volume 1.00 x 10 m is formed under pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamond's bulk modulus to be B =194 GPa. Use the rules of significant figures.Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.28 ✕ 10−6 m3 is formed under a pressure of 4.60 GPa. Find the change in its volume (in m3) when it is released from the press and brought to atmospheric pressure. Take the diamond's bulk modulus to be B = 194 GPa. (Assume the system is at sea level.)
- The illustrated belt is made of rubber (E= = 4 MPa) and has a thickness of 4 mm. It passes through a pulley whose diameter is 20 cm. The belt is subjected to a tension of 50 N. What must be the minimum width, L, so that the stress does not exceed 200 kPa? Answer: 10.3 cmSome claim that mountain climbers suffer from headaches due not only to a lack of oxygen in the brain, but also to the expansion of the brain in the cranium. Find the fractional change of the brain's volume due to a reduction in pressure from (1.48x10^2) kPa at sea level to 27.0 kPa high in the Himalayas. The bulk modulus is 2.10 GPa. Give your answer with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 AnswerI have tried 16.7x10^3, 16.7x10^4, and 1.365x10^8 and those are all wrong for the first part. I know that the second part is 14.3 hr. I need to know the km/s. Thank you!!