Q6/ A V-belt having a lap angle of 180° have a cross sectional area of 6.2 cm² and runs in a groove of inclined angle of 40°. The density of belt is 0.0013 kg/cm and maximum stress is limited to 400 N/cm? and u = 0.2. Find the maximum power that can be transmitted, if the pulley has mean diameter of 30 cm and runs at 1000 rpm.

Q6/ A V-belt having a lap angle of 180° have a cross sectional area of 6.2 cm² and runs in a groove of inclined angle of 40°. The density of belt is 0.0013 kg/cm and maximum stress is limited to 400 N/cm? and u = 0.2. Find the maximum power that can be transmitted, if the pulley has mean diameter of 30 cm and runs at 1000 rpm.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

An aircraft designer is considering the design of an aircraft wing. The wing is to be straight and is to have the same airfoil section all the way along the span; this 2D section has a lift curve slope of 5.9 per radian and a zero-lift angle of attack of -1.2°. It can be assumed that the span efficiency factor will be equal to 0.9. It is proposed that the aircraft will be cruising at Mach 0.57 at an 5° angle of attack.a) Calculate the 3D lift coefficient if: a. The wing area is 170m2 and the wingspan is 40m. b. The wing area is 170m2 and the wingspan is 25m. b) What is the key disadvantage of a low aspect ratio wing for subsonic aircraft?
An athlete begins with the arm in a relaxed upright position OA, in which the elastic band is not stretched. Then he performs an abduction movement leaving his arm in the horizontal OB position. The elastic modulus of the band is 80.0 N / m, that is, 80.0 N of force is required to stretch the band for each additional meter of elongation. If the entire limb has a mass of 2.50 kg and its center of mass is located 250 mm from the shoulder joint. Determine the magnitude and direction of the moment of force with respect to the shoulder joint.
I need the answer as soon as possible
A uniform ladder of mass 20 kg and length 13 m is resting, with its base on rough horizontal ground at a distance of 5 m from a rough vertical wall. The upper end of the ladder rests against the wall. The ground and the wall have the same coefficient of friction with the ladder. a. Show that if the ladder is stable, then the coefficient of friction satisfies the inequality μ> 0.2 [Sufficient working must be shown if full marks are to be awarded here.] b. If, in fact, μ= 0.36
Every second at Niagara Fall 5.5 X 10^5 kg of water falls an average distance of 20 m. Determine the power generated by this process.
In the clevis shown, find the minimum bolt diameter that will support a load P = 14 kips without exceeding a shearing stress of 14 ksi and a bearing stress of 24 ksi.
14.3 The ABC Company is planning to start a new operation hauling sand to a ready-mix concrete plant. The equipment superintendent estimates that the company-owned 30-yard wheel tractor scrapers can obtain 26-ton loads. He is concerned about the high RR of the units in the sand (RR factor 250lb/ton) and the low tractive ability of the tractors on this job. Will traction be a problem? If so, what do you suggest to help?
Needed to be solved this question correctly in 20 minutes and get the thumbs up please show me neat and clean work for it by hand and also
please answer and label all parts for rating.
Needs Complete typed solution with 100 % accuracy.