A Single-Phase AC Ring Main Distribution System. ABCA, turning in a clockwisedirection, fed at Point A with 230 V, supplies the following loads:Load PointLoad CurrentPower Factor45 A0.8 lag55 A0.9 lagCalculate the Current in Section AB (IAp) of the Distributor if the Total Impedances ofthe various sections (for both go and return cables) are as follows:ZAB = (0.1 + j0.15) N(0.15 + j0.225)NZCA = (0.125 + j0.1875) NZBC%3D

A Single-Phase AC Ring Main Distribution System, ABCA, turning in a clocAWD direction, fed at Point A with 230 V, supplies the following loads: Load Point Load Current Power Factor 0.8 lag 45 A 0.9 lag 55 A Calculate the Current in Section AB (IAR) of the Distributor if the Total Impedances of the various sections (for both go and return cables) are as follows: ZAB = (0.1 + j0.15) N ZBC = (0.15 + j0.225) N ZCA = (0.125 + j0.1875) N %3D

A Single-Phase AC Ring Main Distribution System, ABCA, turning in a clocAWD direction, fed at Point A with 230 V, supplies the following loads: Load Point Load Current Power Factor 0.8 lag 45 A 0.9 lag 55 A Calculate the Current in Section AB (IAR) of the Distributor if the Total Impedances of the various sections (for both go and return cables) are as follows: ZAB = (0.1 + j0.15) N ZBC = (0.15 + j0.225) N ZCA = (0.125 + j0.1875) N %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri = 120Vrms? Np:Ns 6:1 Vp 120 Vac 60 Hz out R = 200 ) O Ovrms O 720Vrms 120Vrms O 20Vrms wi m
Question 1
In a single phase equivalent circuit, the current in the a-phase conductor line is simply the voltage generated in the a-phase winding of the generator divided by the total impedance in the a-phase of the circuit. Select one: O True O False
3. Why the pe;'cenuge impedance drop of the transformers are kept equal during the parallel operation of the same. 4. Plot cos®, and cos®; against load current for both cases.
What size primary conductor can be used for a three-phase, 480V transformer, where the primary overcurrent protection is sized at 175A? a. 1/0 AWG b.2/0 AWG OC. 3/0 AWG d.4/0 AWG
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
For a 50 kVa distribution transformer, which on its high voltage side is 2400 V and on the short-circuit low voltage secondary has a voltage of 240 V with a frequency of 60 Hz, it has a leakage impedance of 0.72+j0.92 Ω on the high voltage side and 0.0070+j0.0090 Ω on the high voltage side low tension. The short-circuit test presented values of 48 V, 20.8 A and 617 W for high voltage. The impedance responsible for the excitation current is 6.32+j43.7 Ω referring to the low voltage side. One open circuit test, with the low voltage side energized, presented the values of 240 V, 5.14 A and 186W. According to the information presented, determine: a. Draw the equivalent circuit on the high voltage side and present the impedance values in the circuit. b.Draw the equivalent circuit on the low voltage side and present the impedance values in the circuit. c. For the high voltage value, calculate the value of the current flowing in the magnetizing impedance. d.Determine the yield for an…
Q1. The following figure shows the differential protection of power transformers with specifications of 20 MVA, 66/11 KV.Trans is No load.If a two-phase short circuit occurs between phases b and ¢ It is desirable to calculate the currents passing through the CTs and relays R, Y, B. If these relays are three overcurrent relays with inverse characteristics as T=0.63 / log (I / Iset) and Iset =0.5A.Will this work for short circuit relays? If yes, which relay works faster and at what time?
Solved Problems: Single-Phase Transformers Problem 1 A 19.2 KVA, 19200/480-V, 60 Hz, single-phase transformer is tested with the following results: Open-circuit test (measured from Low-voltage side ) Voc = 480 V Ioc = 1.25 A Poc = 160W Short-circuit test (measured from high-voltage side ) Vsc = 1150V Isc = 1.00A Psc = 190W a- Calculate and Sketch the equivalent circuit of this transformer when referred to its low-voltage side. The transformer is now loaded: 15 KW load, 0.9 lagging PF, and a load voltage of 450 V. b- Find the voltage on the high-voltage side of the transformer. c- Find the voltage regulation of this transformer.
In the following power system, the base voltage in region 2 is 13.8 kV. The transformer reactance is in per unit. The transmission line and load impedance are in Ohms. 2 3 = 300 Zjoad 13,2 kV Z, = 10 + j100 S MVA ri-ssdi w 10 MVAnizU 13.24 - 132Y kV X, = 0.1 138Y - 69A kV X12 = 0.08 Determine the following a. The base complex power in regions 1, 2, and 3 b. Base voltage in regions 1, 2, and 3 c. Base impedance in regions 1, 2 and 3 d. Base current in regions 1, 2 and 3 e. Actual impedance of transformers 1 and 2.
Consider a 3-phase, 35 kV transformers with N1:N2 = 150:900. Calculate the secondary line voltage on no load if the windings are connected in i) Delta-Star [ ii) Star-Delta
O e. None of these Clear my choice The three phase power and line-line ratings of the below electric power system is given below: Vm ut of M G: 50 MVA 11 KV X= 4% T: 50 MVA 11/20 KV X= 4% M: 43.2 MVA 18 KV X= 4% By choosing 100 MVA and 11 KV on the generator side as base values, the new per unit impedance of the generator is and the new perunit impedance of the motor is 4 A three-phase, 60-Hz lossless transmission line is 350 Km long. The line has a phase constant B of 0.001266825 rad/Km and a su impedance Z of 326.09 N. What is the total receiving end reactive power Qr when the sending end voltage is 230 KV and the re voltage is 219 KV and the power angle & is 15 degrees? out of