A single-line diagram of a three-phase balanced system is given below. All the motors are rated with the same rating. The synchronous generator in the given figure is operating at 20KV, when a bolted three-phase short circuit occurs at point P. Calculate the rated interrupting current rating of circuit breaker B and C, both in per unit and Ampere value.

A single-line diagram of a three-phase balanced system is given below. All the motors are rated with the same rating. The synchronous generator in the given figure is operating at 20KV, when a bolted three-phase short circuit occurs at point P. Calculate the rated interrupting current rating of circuit breaker B and C, both in per unit and Ampere value.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.9P

See similar textbooks

Similar questions

A 350 MVA, 11 kV three-phase generator has a sub transient reactance of 15%. The generator supplies a number of synchronous motors over 64-km transmission line having transformers at both ends, as shown in Figure B3. M: T2 m r M2 Figure B3 Just two equivalent motors represent the motors, all rated 13.2 kV. Rated inputs to the motors are 100 MVA and 50 MVA for M1 and M2, respectively. For both motors X" = 12%. The three-phase transformer T1 is rated 200 MVA, 11/220kV with leakage reactance of 10%. Transformer T2 is composed of three single-phase transformers each rated 220/13.2 kV, 180 MVA with leakage reactance of 12%. Series reactance of the transmission line is 0.5+j0.5 /km. Draw the impedance diagram, with all reactance marked in per-unit. (Select the generator rating as base in the generator circuit)
6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing anglefor the system. The generator is delivering 1.0 p.u power under prefault conditio
This question is about electrical power material and I want to solve it in 20 minutes
2A. What is another term for "shunt"? a) in series b) in parallel c) compounded d) none of the above 2B. Which of the following is/are a basic type of DC generator connection? a) series b) shunt c) compound d) all of the above
Figure below shows a power system. The rating of generators and transformers are:G1:25MVA, 6.6KV, jO.2 p.u. G2:15MVA, 6.6KV, jo.15 p.u. G3:30MVA, 13.2KV, jo.15 p.u. T1: 30MVA, 6.6A- 115Y KV, jo.1 p.u.T2: 15MVA, 6.6A- 115Y KV, jo.1 p.u. T3:single phase units each rated 10MVA, 69/ 6.9 KV, jo.1 p.u. Find te reactances in p.u, take a base of 30MVA, 6.6 KV in the circuit of G1 .=.XG1 G2} 4 A lubu T2 T1 T3 G1 G3 j120 2 j90 N
Please solve d, e, f ONLY.
explain why Transformers are necessary in all stages of power distribution systems. Three-phase voltages may be stepped up or down by three-phase transformers
G1 Bus 1 Bus 2 Line Bus 3 T2 Bus4 M1 j402 25 MVA Ye A 13.0 kV Xg1 =10% зо мVA 13.4/69 kV 20 MVA 66/13.2 kV 15 MVA 13.0 kV Xmi =15% 10% 10% e direct-axis subtransient reactances of the synchronous generator and otor are given above in the figure. The fault impedance (ZA) is 15.87 ohm ie generating is operating 25 MVA, 0.95 p.f. lagging, and at 10% above rate Itage when a three-phase fault occurs at bus 1. Determine each three-phase ult
(b) A three-phase A-connected synchronous generator is rated at 120 MVA, 10.5 kV, 0.85 PF leading and 60 Hz. Its synchronous reactance is 1.4 N, and its resistance may be ignored. Analyse the voltage regulation of this generator.
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
Determine the positive- and negative-sequence phase shifts for the three- phase transformers shown in Figure 3.36.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.