A simple beam with a span length of 6m is subjected by a distributed live load of (9.6+0.8+0.7)kN/m on whole span length. A beam is a reinforced concrete with a unit weight of 24.5kN/m3, (150+10)mm width and (300+140)mm depth. Determine the total reaction on each support due to the weight and live load. Use 18.4L +1.6LL equation in computing for the total reaction on each support.

Q: In a plate girder subjected to a bending moment of 200 kNm, the width and thickness of flange are…

A:

Q: A reinforced concrete beam has a width of 425mm and an effective depth of 900mm. The longitudinal…

A: The given data is shown below: Width=425 mmEffective depth=900 mmCompresion…

Q: 2. A timber beam has a span of 5 meters and carries a uniform load of 10 KN/m. The dimension of the…

A:

Q: From the given figure below, determine the maximum flexural stress of the beam if it has a cross…

A: Determine the maximum flexural stress of the beam?

Q: Compute the maximum flexure stresses for the beam loaded shown 15 KN/m 2m 150 mm 250 mm w=6KN/m 3m…

A: Given data in question  UDL point load Span member length  Cross section To find out  Bending stress…

Q: reinforced concrete beam, b by h with tensile reinforcement of 6-25mm diameter bars is simply…

A: 1. To compute the moment capacity of concrete in kN-m, we need to first determine the concrete…

Q: A reinforced concrete beam having a width of 500 mm and an effective depth of 750 mm is reinforced…

A: - Ultimate Moment due to UDL on simple beam will be  ; M = wl28 =50 × 1028 = 625 KN-m - Find x lim :…

Q: Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply…

A:

Q: An I-section girder, 200 mm wide by 300 mm deep, with flange and web of thickness 20 mm is used as a…

A:

Q: A reinforced concrete T-beam spaced at 3.0 m on centers has a span of 4.0 m with a slab thickness of…

A:

Q: A pontoon bridge is constructed of two longitudinal wood beams, known as balks that span between…

A: Given: The uniform floor load is 8 kPa. The length of chesses is 2 m. The length of balks is 3 m.…

Q: effective depth of 550mm and the width of the web section is 300mm. It is reinforced at the bottom…

A:

Q: 60KN A D ANALYZE THE STRUCTURE USING PORTAL FRAME METHOD Compute: 1. Axial Load of AD 2. 3. Show…

A:

Q: Question The span of cantilever beam is 2 m. The cross-section of the beam is a hollow square with…

A: A cantilever beam- span of the beam-L=2 m=2000 mm,sides of square=100 mm,Moment of inertia I=4×105…

Q: Determine the ultimate moment capacity of the reinforced concrete beam if it is reinforced with…

A: Given: b = 400 mm h = 600 mm Tension bars of 6-25mm  fc = 20.71 MPa fy = 414 MPa

Q: A 6-m simply supported reinforced concrete rectangular beam is 250 mm wide. The total depth is 400…

A:

Q: 1. Compute the moment capacity of concrete in kN-m. 2. Compute the moment capacity of steel in kN-m.…

A: 1. To compute the moment capacity of concrete in kN-m, we need to first determine the concrete…

Q: A simply supported beam 300mm x 500mm has a spa unbonded tendons. fse = 750 MPa, Aps = 1200m above…

A:

Q: A rectangular concrete beam has a width of 400mm and an effective depth of 700mm. It is reinforced…

A: Given : Width =400mm, effective depth = 700mm 5-28 mm diameter bar  Required : Ultimate moment…

Q: 4. A 10 m span simply supported beam carries a uniform load. The beam has an adequate lateral…

A:

Q: Construct the V and M diagram of the beam loaded as shown. Answer: Max. Moment = 40 KN 20 kN/m 50 KN…

A:

Q: SITUATION 20: The T-beam in the floor system has a slab thickness of 100 mm and supported by beams…

A:

Q: Q-A steel cantilever beam is proposed to build into a concrete wall at one end, and the other end is…

A: Given data: Dead load, D.L.=20 kNm Live load, L.L.=10 kNm The length of beam, l = 5 m Yield strength…

Q: A 350mm x 500 mm rectangular beam is reinforced for tension only with 5 – 28mm dia bars. The beam…

A: given that  Rectangular beam dimensions = 350mm x 500mm Reinforcement = 5 bars with 28mm diameter…

Q: a.) The ultimate moment capacity of the concrete section in kN-m b.) The maximum value of P in kN

A:

Q: A rectangular beam reinforced for tension has b = 300mm, d = 480mm. The beam is reinforced with 7…

A: Width of beam, Effective depth of beam, Reinforcement barsCompressive strength of concrete, Yield…

Q: 2. A reinforced concrete rectangular beam has a width of 300 mm and an effective depth to bottom…

A:

Q: Problem 2: A reinforced concrete T-beam has a slab thickness of 100 mm which is supported by 6 m…

A: T-beam slab thickness=100 mm, Span length=6 m, Web width(bw)=300 mm, Effective depth(df)=500 mm,…

Q: A reinforced concrete beam has a width of 30 mm and an overall depth of 480 mm. The beam is simply…

A: Maximum factored Moment and factored load Factored Load and moment are the load and moment that we…

Q: CLO 2: The girder of a simple log bridge supports a wheel load W acting at any position along the…

A:

Q: 5. A beam has a width of 300mm and effective depth of 540mm. d = 60mm. It is reinforced with 8-25mm…

A: f'c =21MPa,. fy= 420 MPa (assumed for design)

Q: A reinforced concrete T-beam has an effective flange width of 750mm with a slab thickness of 100 mm.…

A: Consider the following diagram:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.