A simply supported beam spans 8 m. the cross section width is 300mm, the effective depth is 500mm. It is required to carry a uniformly distributed load of 150 kN/m at ULS. Assume fo=30 MPa and fy=500 MPa. Design the beam for both bending and %3D shear.

A simply supported beam spans 8 m. the cross section width is 300mm, the effective depth is 500mm. It is required to carry a uniformly distributed load of 150 kN/m at ULS. Assume fo=30 MPa and fy=500 MPa. Design the beam for both bending and %3D shear.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: B A L1 W d tw do bf L2 Figura 1. Elevación frontal de marco estructural D H1 Figura 2. Detalle de la…

A: I am solving first three sub parts as bartleby guidelines..

Q: A rectangular section of size 100mm x 200 mm is used as a simply supported beam of 5m length. It is…

A: Given data : Width (B)=100 mmDepth (D)=200 mmLength of beam (L)=5 mCentral point load (W)=250 KNTo…

Q: Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by…

A: Overhang Beam : Overhanging beam is type of beam in which the beam extends beyond the end support of…

Q: A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an…

Q: Q- A simply supported rectangular beam having span 5m is subjected to a central point load of 50 kN.…

A: Given- Span=5 m load=50 kN Stress=220 N/mm2,

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

Q: 225 P,- 8 P,- 10 9- 18 2 (m) 1 (m) 4.50 (m) 1.50 (m)

Q: Problem 3 A Determine the maximum flexural stress (MPa) developed for the beam loaded as shown.…

Q: 23: The beam shown in Figure 3 is subjected he moving load shown . Determine (a) the naximum…

A: Given Force exerted by rear axle =71.17 KN Force exerted by front axle =17.79 KN

Q: A beam has a width of 300mm and effective depth of 540mm, d' = 60mm. It is reinforced with 4-25mm…

A: fc = 25 MPa (assuming) fy = 420MPa (assuming) d = 540mm b = 300mm d' = 60mm (effective cover)…

Q: property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B,…

Q: Prob 3. The beam below has an allowable normal stress of oallow = 24 ksi and an allowable shear…

Q: 23/Find the maximum shear stress. 4 kN/m 5 kN Im 2 kN.m 2m 2m 2m 2m 5 mm E=200 GPA 20 mm -50 mm-…

Q: a beam having a width of 300 mm and a depth of 600 mm carries a dead load of 24 kn/m (including its…

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

A: As per company's guidelines we can only answer first question Kindly post other questions as…

Q: P=20.08 The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (a)…

Q: Q1: A simple supported beam of 5 m has a cross section (150*250) mm. If the permissible bending…

A: Given it is a case of simply supported beam length of beam=5m width of beam=150mm=0.15m depth of…

Q: A cantilever beam of length 4 m, is subjected to an Uniformly distributed load of 26 kN/m for entire…

A: Given data, L= 4 m w = 26 kN/m D = 200 mm t = 30 mm E = 100 GPa

Q: Q1: A simple supported beam of 5 m has a cross section (150*250) mm. If the permissible bending…

Q: 50 kN 5kN/m В C VD A I 70 kN - 3 m - 5 m -2 m W200 × 19.3 Draw the shear-bending moment diagram of…

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

Q: 2: A reinforced concrete beam has a simple span of 4.5 m. and carries a dead load, including…

A: Given dataspan=l=4.5mself weight=dead load=20kN/mlive load=35 kN/mclear cover=75mmfc'=28 MPafy=415…

Q: A beam 300mm X 600mm with a span of 6m is fixed at both ends. The beam carries a superimposed load…

Q: QI/ A simply supported pretensioned concrete beam of span 12 m has mid-span section shown in Fig…

Q: The mass of the block and thus the total downward pull of gravity are the same on slopes with angles…

A: Ans: True Explanation: given in step 2

Q: A simple supported beam spans 10 m and supports a specified uniform live load of 8 KN/m and a…

A: The given data is as follows: Span length of beam=10 mUniform live load on beam=8 kN/mConcentrated…

Q: Analyze the structure below using cantilever beam method 25KN C 3m 50KN B E. H 4m -6m- 8m- ml

A: Data Given: Asked: Axial load at HI

Q: 1.5m 4m H 5kN 2.5kN/m 5m 1.5m/ L

Q: Design of Singly Reinforced Beams 1. A simply supported beam is 6 meters long and is reinforced as…

A: Given data: As=4×π4×252=1963.495 mm2d=400 mmb=250 mmfc'=35 MPafy=400 MPaL=6 mDL=26 kN/m

Q: depin a simple span beam of 8 m in length with overhang. a uniform load of 12.0 KN/m and its own…

Q: Working stress design method 3/ By using the working stress design method find the maximum flexural…

A: Answer We know that stress in concrete is given by fc = M*ycIN.A And stress in steel is given by fs…

Q: In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 60…

Q: A cantilever beam of length 4m with a square section of side length 0.1 m is loaded vertically at…

Q: A rectangular beam reinforced for tension has b = 300mm, d = 480mm. The beam is reinforced with 7…

A: Width of beam, Effective depth of beam, Reinforcement barsCompressive strength of concrete, Yield…

Q: Determine the Global stiffness matrix of the continuous beam shown. Assume EI is 150kN -m² is…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

A simply supported beam spans 8 m. the cross section width is
300mm, the effective depth is 500mm. It is required to carry a
uniformly distributed load of 150 kN/m at ULS. Assume fe=30
MPa and fuk=500 MPa. Design the beam for both bending and
shear.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Soil
15 mm PROBLEM 6.9 -250 mm 65 kN 90 kN 65 kN 0.3 m (300 пm) For the beam and loading shown, consider section n-n and determine (a) the largest shearing stress in that section, (b) the shearing stress at point a. 25 mm 250 mm 10 mm 15 mm 06 m 06 m 06m 06 m
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t, = 9mm Flange Width, B; =112.5 mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,=200 MPa on single shear, o,-260MPA on double shear. 1. Determine the location of centroid, y, from top of the beam in mm. 2. Determine the moment of inertia, I, of the section in mm“. 3. Determine the maximum allowable moment, Mall, in kn-m, base on the beam's cross-section.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an effective depth of 600 mm. The beam carries a dead load moment of 280 kN-m and a live load moment of 525 kN-m. It has a span of 5.4 m and a spacing center to center of 1.8 m. Use reduction factor ø=0.90, fc’=20.7 MPa, fy = 344.7 MPa.Determine the effective width of flange. Determine depth of compression flange. Determine the required steel area. See the formula in the image
A rectangular beam with limited size of 300mm is to be designed for an ultimate moment of 550 kN·m with f’c = 28 MPa and fy = 420 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. 13. Determine the the maximum tensile steel ratio if the tensile steel strain will not be less than 0.005 for a more ductile failure.
A Universal beam of I shaped cross-section is 203 mm deep, and 133 mm wide and has a steel plate 150 mm by 10 mm thick fastened to each flange. Ix-x for the universal beam is 28.80×10^6 mm^4. a) Determine the total uniformity distributed load which may be carried over a simply supported span of 6 metres if the permissible bending stress is 165 N/mm^2. Neglect the self-weight of the beam. [Ans.: 124.02 KN/m] b) Determine the minimum central length over which the additional plates are required. [Ans.: 4.23m]
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.