A rectangular beam has a width of 250 mm and an effective depth of 400 mm. The beam is reinforced at the top and bottom section with a steel covering of 75 mm for the compression bars and has a simple span of 6 meters. It carries a uniform live load of 36 kN/m and a dead load of 15 kN/m. If fc = 21 Mpa, fy = 276 Mpa, solve the following: 1. Ultimate uniform load 2. Nominal moment capacity of the beam at balanced condition 3. Total steel area in tension

A rectangular beam has a width of 250 mm and an effective depth of 400 mm. The beam is reinforced at the top and bottom section with a steel covering of 75 mm for the compression bars and has a simple span of 6 meters. It carries a uniform live load of 36 kN/m and a dead load of 15 kN/m. If fc = 21 Mpa, fy = 276 Mpa, solve the following: 1. Ultimate uniform load 2. Nominal moment capacity of the beam at balanced condition 3. Total steel area in tension

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

INFLUENCE LINE PROBLEM a. Determine the maximum positive ordinate for member DC. b. Determine the location of a point load that will give the maximum compressive force for member AB. show solution asap ,answers in 4 decimal places
[ series of concentrated axle loads ] Determine the following: a. Maximum negative shear at B b. Maximum positive shear at B c. Maximum positive moment at B d. Maximum reaction at C Use stored values while solving 4 decimal places in final answer
Reinforced And Prestressed Concrete PROBLEM: A reinforced rectangular beam with width b and effective depth d has 4 -16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa b= 275 mm d= 440 mm L= 3.85 m Wd = 19.25 kN/m WL = 24.75 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
mm on its side, just 2. A cantilever, made of a certain material, of 2 m length and square section fails in bending when a point load of N is placed at its free end. A beam of rectangular cross section, and made of same material, 150 mm wide and 300 mm deep, is simply supported over a span of 3 m. Calculate: (a) the stress at which the cantilever beam fails in kPa and (b) the maximum concentrated load that the beam can carry at its center without failure in kN. 2 m (a) Cantilever kN THIS |— 1.5 m —— 1.5 m—| (b) Simply supported beam 150 300
Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression.
Q1: Design a simply supported rectangular reinforced concrete beam. Note: The self-weight of the beam is not included. RT 55 kN W = 24 kN/m u (D.L) Wa L.L) 15 kN/m 550 mm 2 m 250 mm 7 m
Structural Analysis: Solve the F4-5
With FBD
A cantilever beam has the cross-section of an isosceles triangle and is loaded as shown below : 1m- دکنند.نید 3 MNm Fig. 6.21. If moment of inertia of the cross-section is induced in the beam. 1 m4, determine the maximum bending stress 36 1 for a triangular section,
STEEL DESIGN Situation 1: Situation 3: A light crane rail sits on and is securely fastened to a W crane girder. The girder is simply supported on a span of 6 m. The crane wheel loads are as follows: V = 80 kN and H = 8 kN. Assume full transfer of lateral load to the top flange of the girder. An 8-m long steel column is pinned at the top and fixed at the bottom. The column is provided with lateral support at mid-height in the weak direction. Properties: Ix = 178.1 x 10 mm4 Girder properties: ly = 18.8 x 106 mm4 A = 8129 mm²2 Weight = 67 kg/m Sx = 1, 280 x 10³ mm3 Sy = 361 x 103 mm3 7. Determine the critical slenderness ratio. a. 38 c. 27 Allowable stresses: b. 83 d. 41 Fbx = 164 MPa Find the critical buckling load. 9270 kN Fby = 186 MPa 8. 2190 kN 2310 kN a. с. Determine the actual bending stress about the x- axis. 1. b. 4730 kN d. Compute the minimum length of the column for which the Euler's formula is valid if the proportional limit of the steel used is 320 MPa. a. 99.12 MPa С. 93.75…