a si 8-53.. A lantern of weight W is suspended at the end horizontal bar of weight w and length L that is supported by a cable that makes an angle with the side of a vertical wall. Assume the weight of the bar is at its center. (a) Derive an equation for the tension in the cable. (b) Calculate the tension in the cable for a bar of weight 28 N and length 1.5 m, plus a lantern of weight 85 N, and the cable making a 37° angle to the vertical. 10* D

a si 8-53.. A lantern of weight W is suspended at the end horizontal bar of weight w and length L that is supported by a cable that makes an angle with the side of a vertical wall. Assume the weight of the bar is at its center. (a) Derive an equation for the tension in the cable. (b) Calculate the tension in the cable for a bar of weight 28 N and length 1.5 m, plus a lantern of weight 85 N, and the cable making a 37° angle to the vertical. 10* D

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

One end of a uniform rod of weight w = 74.0 N and length L = 2.85 m is supported by a cable at an angle of 0 = 34.0° above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. -Support -L- Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable. n = T =
Chapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 2.7 m and its weight is 220 N. Also, let the block's weight W = 280 N and the angle 0 = 27°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? com A (a) Number Units (b) Number Units (c) Number Units Click if you would like to Show Work for this question: Open Show Work
In the figure below, a uniform beam of weight 420 N and length 2.8 m is suspended horizontally. On the left it is hinged to a wall; on the right is it supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. Cable Beam (a) What value of D corresponds to that tension? (b) Give any value for D that won't snap the cable. m
A uniform 8.00 m, 1500 kg beam is hinged to a wall and supported by a thin cable attached 2.00 m from the free end of the beam. The beam is fixed to the wall at an angle of 30 degrees above the horizontal. The angle between the cable and the beam is 40 degrees. What are the unknowns? -direction of tension in the cable -direction of the hinge force -magnitude of rhe tension in the cable -magnitude of the hinge force
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A ladder of weight 600 N and length 10.0 m is placed against a smooth vertical wall. A person weighing 1000 N stands on the ladder 6.0 m from the bottom as measured along the ladder. At a height of 7.0 m the ladder is on the point of slipping. Find: (a) Calculate the force exerted by the wall. (b) Calculate the normal force exerted by the floor on the ladder. (c) The force of friction between the floor and ladder. (d) Calculate the coefficient of static friction if the ladder is on the point of slipping when the person is 8.0 m up the ladder.
In the figure, one end of a uniform beam of weight 350 N is hinged to a wall; the other end is supported by a wire that makes angles - 26° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. (a) Number (b) Number (c) Number i i Units Units Units Hinge 8 > <
In the figure, one end of a uniform beam of weight 100 N is hinged to a wall; the other end is supported by a wire that makes angles 8- 29 with both wall and beam. Find (a) the tension in the wire and the (b) horizontal anid (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units Units (b) Number Units (c) Nurmiber
One end of a uniform { = 4.30-m-long rod of weight w is supported by a cable at an angle of 0 = 37° with the rod. The other end rests against a wall, where it is held by friction (see figure). The coefficient of static friction between the wall and the rod is µ. = 0.490. Determine the minimum distance x from point A at which an additional weight w (the same as the weight of the rod) can be hung without causing the rod to slip at point A. B Need Help? Read It Watch It
(b) In the figure below, a uniform beam of weight 500 N and length 3.0 m is suspended horizontally. On the left it is hinged to a wall; on the right it is sup- ported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. (a) What value of D corresponds to that tension? (b) To prevent the cable from snapping, should D be increased or decreased from that value? D Cable Beam
In a city park a nonuniform wooden beam 4.00 m long is suspended horizontally by a light steel cable at each end. The cable at the left-hand end makes an angle of 30.0° with the vertical and has tension 620 N. The cable at the right-hand end of the beam makes an angle of 50.0° with the vertical. As an employee of the Parks and Recreation Department, you are asked to find the weight of the beam and the location of its center of gravity.
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor. The ladders weigh 600 N and 450 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope.