In the figure, one end of a uniform beam of weight 100 N is hinged to a wall; the other end is supported by a wire that makes angles 0- 29 with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units (b) Number Units

In the figure, one end of a uniform beam of weight 100 N is hinged to a wall; the other end is supported by a wire that makes angles 0- 29 with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units (b) Number Units

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A uniform beam of length 12.0 m and weight 690 N is connected to a wall by a bolt, and is supported by two cables. Cable 1 makes an angle of 25.0 Degrees with the beam, is attached 5.00 m from wall, and has a tension of 312 N. Cable 2 makes an angle of 39.0 Degrees with the beam and is attached to the end of the beam. The system is in static equilibrium. What is the tension in cable 2?
The system in the figure is in equilibrium. A concrete block of mass 254 kg hangs from the end of the uniform strut of mass 59.7 kg. For angles -28.9° and 9-57.2%, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge. Sarut z Hinge (a) Number Units (b) Number Units (c) Number i Units
In the figure below, a uniform beam of weight 420 N and length 2.8 m is suspended horizontally. On the left it is hinged to a wall; on the right is it supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. Cable Beam (a) What value of D corresponds to that tension? (b) Give any value for D that won't snap the cable. m
21. Go The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle 0 = 39° by a brace that is attached to a pin. The beam has a weight of 340 N. Three additional forces keep the beam in equilibrium. The brace applies a force P to the right end of the beam that is directed upward at the angle 0 with respect to the horizontal. The hinge applies a force to the left end of the beam that has a horizontal component í and a vertical component V. Find the magnitudes of these three forces. Вeam Hinge Pin Brace
A uniform 8.00 m, 1500 kg beam is hinged to a wall and supported by a thin cable attached 2.00 m from the free end of the beam. The beam is fixed to the wall at an angle of 30 degrees above the horizontal. The angle between the cable and the beam is 40 degrees. What are the unknowns? -direction of tension in the cable -direction of the hinge force -magnitude of rhe tension in the cable -magnitude of the hinge force
The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless hinge and supported from below at an angle θ = 35o by a brace that is attached to a pin. The beam has a weight of 342 N. Three additional forces keep the beam in equilibrium. The brace applies a force P¯ to the right end of the beam that is directed upward at the angle θ with respect to the horizontal. The hinge applies a force to the left end of the beam that has a horizontal component H¯ and a vertical component V¯. Find the magnitudes of these three forces.
A straight ladder is leaning against the wall of a house. The ladder has rails 4.90 m long, joined by rungs 0.410 m long. Its bottom end is on solid but sloping ground so that the top of the ladder is 0.690 m to the left of where it should be, and the ladder is unsafe to climb. You want to put a flat rock under one foot of the ladder to compensate for the slope of the ground. (a) What should be the thickness of the rock? (b) Does using ideas from this chapter make it easier to explain the solution to part (a)? Explain your answer.
The system in the figure is in equilibrium. A concrete block of mass 307 kg hangs from the end of the uniform strut of mass 41.1 kg. For angles = 34.6° and 0 = 55.5°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge. Strut T z 8 -Hinge (a) Number (b) Number (c) Number Units Units Units
In the figure, one end of a uniform beam of weight 120 N is hinged to a wall; the other end is supported by a wire that makes angles e = 25° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units (b) Number Units (c) Number Units
The system in the figure is in equilibrium. A concrete block of mass 337 kg hangs from the end of the uniform strut of mass 53.5 kg. For angles = 33.3° and 0 = 57.5°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge. (a) Number i (b) Number (c) Number i Units Units Units Strut A -Hinge >
In the figure, one end of a uniform beam of weight 350 N is hinged to a wall; the other end is supported by a wire that makes angles - 26° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. (a) Number (b) Number (c) Number i i Units Units Units Hinge 8 > <
2. A uniform rod of length I = 4m and mass m = 75kg is hinged to a wall at the left and supported at the right by a cable. The cable is attached to the rod one meter from its right edge. The rod makes a 30° angle with the horizontal and the cable makes a 45° angle with the rod. Calculate the tension in the cable and the reaction forces on the hinge support). cable wall rod 45° 30° hinge