**Chapter 12, Problem 029**A door has a height of 2.1 m along a y axis that extends vertically upward and a width of 1.05 m along an x axis that extends outward from the hinged edge of the door. A hinge 0.23 m from the top and a hinge 0.23 m from the bottom each support half the door's mass, which is 16 kg. In unit-vector notation, what are the forces on the door at (a) the top hinge and (b) the bottom hinge?(a) Number \(\_\_\_\_\) i + \(\_\_\_\_\) j Units(b) Number \(\_\_\_\_\) i + \(\_\_\_\_\) j UnitsClick if you would like to Show Work for this question: [Open Show Work](#)**Links:**- [LINK TO TEXT](#)- [LINK TO SAMPLE PROBLEM](#)- [LINK TO SAMPLE PROBLEM](#)- [VIDEO MINI-LECTURE](#)

Using Newtons law and torque about the hinges

Answered: A door has a height of 2.1 m along a y…

Similar questions

Problem #2: A 50.0-kg sign hangs from the end of a uniform strut. The strut is 4.0 m long and weighs 400.0 N. The strut is supported by a hinge at the wall and by a cable whose other end is tied to the wall at a point 3.0 m above the left end of the strut. Find a. the tension in the supporting cable b. the force of the hinge on the strut (magnitude and direction). 5.0 m 3.0 m 4.0 m GAS
A 1,300 N shaft is held in place by a light wire at an angle 0 = 29.0° to the horizontal as shown in the figure. The shaft is attached to a pivot at the bottom, and a mass of weight w = 2,075 N hangs from its top. The shaft makes an angle of Q = 61.0° with the horizontal. Assume the shaft is uniform. A 31 m (a) Find the tension in the supporting wire (in kN). KN (b) Find the components of the reaction force (in kN) exerted by the floor on the shaft. horizontal component: magnitude direction KN right vertical component: magnitude direction upward KN ¾ >
A long thin solid rod lies along the positive x-axis. One end is at x = 1.50 m and the other at x = 3.70 m. The linear mass density is A = ax3 + bx, where A is measured in kg/m, and the constants have the following values: a = 1.60 kg/m4 and b = 2.80 kg/m². Determine the total mass of the rod. Submit Answer Tries 0/10 Calculate the x-coordinate of the center of the mass for this rod. Submit Answer Tries 0/10
An 8-m-long beam, weighing 14,700 N, is hinged to a wall and supported by a light rope that is attached 2.0 m from the free end of the beam. If the beam is supported at an angle of 30.0° above the horizontal, (a) find the tension in the rope and (b) the reaction force of the wall on the beam. 40.0° 2.0 m 30.0°
Chapter 12, Problem 021 The system in the figure is in equilibrium. A concrete block of mass 285 kg hangs from the end of the uniform strut of mass 36.7 kg. For angles o = 35.1° and e = 69.4°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge. Strut Hinge (a) Number Units (b) Number Units (c) Number Units
A uniform plank is supported by two vertical wires attached to its ends. A small mass rests on the plank. The plank is balanced horizontally. It has a mass of 250 kg and is 5.50 m long. A small mass of 11.0 kg is 2.00 m from the left end of the plank. What is the tensions in the left wire? Assume the units are Newtons, and type in the numerical answer to three significant figures.
The diagram shows a uniform 30 cm strut weighing 5 N supporting a 10 N weight 10 cm from the pivot. Find the tension in the cable attached to the wall. 10 cm 10 N 30°
Do Chapter 12, Problem 11a. (Problem 19a in the 9th ed.) Calculate the tension in the cable, in Newtons. θ = 20o d = 1 m ℓ = 8 m M = 2,000 kg Cable's distance from the hinge (5 m in the text) is c = 5 m h = 12 m Lot's mass (1000 kg in the text) is m = 1,000 kg
A door has a height of 2.1 m along a y axis that extends vertically upward and a width of 1.08 m along an x axis that extends outward from the hinged edge of the door. A hinge 0.21 m from the top and a hinge 0.21 m from the bottom each support half the door's mass, which is 19 kg. In unit-vector notation, what are the forces on the door at (a) the top hinge and (b) the bottom hinge? (a) Number j Units (b) Number j Units
Two structural members A and B are bolted to a bracket as shown. Knowing that both members are in compression and that the force is P = 35 kN in member A and Q=10 kN in member B, determine by trigonometry the magnitude and direction of the resultant of the forces applied to the bracket by members A and B. 40° A -20° The magnitude of the resultant of the forces applied to the bracket by members A and B is The direction of the resultant of the forces applied to the bracket by members A and B is KN.
A uniform plank of wood has a mass of 19.5kg and a length of 2.0m. A person holds the plank using both hands. The first hand exerts a downward force, F⃗ , at an end of the plank. The second hand exerts an upward force, F⃗ 2, at a distance of 50.0cm from the same end of the plank. What is the magnitude, in newtons, of the force F⃗ 2 What is the magnitude, in newtons, of the force F⃗ 1?
Directions: Assume, unless otherwise specified, that all numbers have at least 3 significant figures. F (N) Students collect data, see graph, for the force involved in stretching a rubber band. The data is well fit by the equation F = 33.65 x0.4971, 12 10 where F is in newtons and x is in meters. One end of the rubber band is attached to a stationary vertical rod and the other end to a 0.3 kg mass. The mass rests on a frictionless horizontal surface. The mass is pulled back such that the rubber band is stretched by 0.8 m from its unstretched length and then released from rest. 4. x (m) 0,1 0.02 0.04 0.06 0.08 A. What is the speed of the mass after it has traveled 0.4 m? B. What is the maximum speed of the object?

SEE MORE QUESTIONS