A short hollow cylindrical steel compression member is required to support an axialload of 180 kN. The material used can carry maximum compressive stress of 95 MPa.Determine the inner and outer diameter of the member if it is 6 mm thick and 200 mmlong.

Answered: Image /qna-images/answer/04fc60b4-4e8e-4eba-9acb-27c66162500c.jpg

Answered: A short hollow cylindrical steel…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solid
solve the problem
5. The rod bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C and D. The allowable stresses are 125 MPa in steel, 70 MPa in the brass, and 85 MPa in the aluminum. Assume that the allowable stresses are the same for tension (T) and compression (C). (a) Determine the diameter required for the brass bar. (b) Determine the required diameter for the steel bar. (c) Determine the required diameter for the aluminum bar. Express your answer in millimeters. Steel Brass C Aluminum B A 100 kN 85 kN 200 kN 215 kN 0.5 m 0.5 m 0.5 m
Complete solutions and diagrams please. Need asap
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
SOLVE COMPLETELY. SHOW COMPLETE SOLUTION, INCLUDE FBD
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
A gusset plate is connected to the flange of column with the help of fillet weld on both sides as shown in the figure. The direct shear stress and bending tensile stress are 70 MPa and 130 MPa respectively. Find the equivalent stress (in GPa). Gusset plate I-section flange
determine the minimum thickness of the steel bar. answer set c only
Please show all steps
A high-strength steel band saw, 29 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 290? Assume E = 210 GPa. Answer must be in mm.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A short hollow cylindrical steel compression member is required to support an axial load of 180 kN. The material used can carry maximum compressive stress of 95 MPa. Determine the inner and outer diameter of the member if it is 6 mm thick and 200 mm long.