A shell and tube heat exchanger operates with two shell passes and four tube passes. The shell fluid is ethylene glycol which is cooled from 140c to 80c & ( Cp = 2742). Watue flows in the tubes, entering at 35c and leaving at 85c. The overall HTC for this arrangement is 850 w /m2k . Calculate the flow rate of water required and the area of the the H. E. ?

A shell and tube heat exchanger operates with two shell passes and four tube passes. The shell fluid is ethylene glycol which is cooled from 140c to 80c & ( Cp = 2742). Watue flows in the tubes, entering at 35c and leaving at 85c. The overall HTC for this arrangement is 850 w /m2k . Calculate the flow rate of water required and the area of the the H. E. ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ps: the mass flow rate of the engine oil is 0.32 kg/s and the velocity of water is 0.04 m/s, and analyze the performance of the heat exchanger compared to the desirable condition
PROBLEM # 22.a. mass 1020 kg /min, the temperature of hot water is being decreased from to 212.09 oF using a heat exchanger. at a a pressure = 2at m and flow rate = 248.09°F Reservoir waten u used as W coolant with mass flow rate = 1800 kalmin and inlet temperature = 50.09 of. The minimun allow able surface are a = 270. 17 ft o4 heat ex changer 2. %3D all ow able overall heat = 204.05 btu/ The transfer coefficient of heat exchanger maxi mum %3D 2 The heat to be use d must be capaci ty of inet and outlet temperatures the average value Find the Number of Transfer units (NTU) using effective ness esch anger wsing NTU metho d if the heat being used is heat exchanger parallel - flow double-pipe
Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810 J/kg. °C) from 66 °C to 39 °C.Water (Cp = 4200 J/kg. °C) at 10 °C is pumped at 4750 kg/h to cool the solution. The tube side fluid flows in a circular pipe with an outside diameter of 25 mm. The overall heat transfer coefficient is (6.84x10^2) W/(m².°C). Find the tube length 'L' for one pass of a two-pass parallel flow double-pipe heat exchanger as shown in Figure. Answer should be in m with three significant figures.
QUESTION 6 En. Karim recently bought a 2-shell passes and 12-tube passes type heat exchanger for his metal factory to reduce the hot oil (cp = 2200 J/kg.K) temperature. The hot oil enters the heat exchanger through the shell passes at 160 °C with a flow rate of 0,2 kg/s. The coolant fluid used to reduce the hot oil temperature is water (cp = 4180 J/kg.K). Water flows through the heat exchanger pipe at 18 °C and at flow rate of 0.1 kg/s. The tube inside the heat exchanger is made of 1.8 cm diameter copper tube and the length is 3 m. If the overall heat transfer coefficient is 340 W/m².K, evaluate and discuss your finding for the following parameters; i. The maximum rate of heat transfer, ii. The actual rate of heat transfer, iii. The outlet temperatures of the water, and iv. The outlet temperatures of the oil.
Find the heat capacity of the hot and cold fluid.
helpp
I need answer in 1hr do it fast. A shell-and-tube heat exchanger is set at the one shell pass and two tube passes. Hot air enters the shell at 90°C, and leaves at 50°C, whose mass flow rate is 5 kg/s. Cold water enters the tube at 23°C, whose flow rate is 3 kg/s. What is the water outlet temperature? What is the overall UA of the heat exchanger? a) Draw the problem diagram. b) List all required properties and equations to solve this problem. c) Solve the problem
Water must be heated from 15 to 50°C in a simple double-pipe heat exchanger at a rate of 3,500 kg/h. The water is flowing inside the inner tube with steam condensing at 110°C on the outside. The tube wall is so thin that the wall resistance may be neglected. Assume that the steam-film coefficient h_0 is 11 kW/m^2 °C. What is the length of the shortest heat exchanger that will heat the water to the desired temperature, considering an optimal diameter for the tube? Checking several table values, the following properties of water for this scenario are: p = 993 kg/m^3 k = 0.61 W/m °C \mu (viscosity) = 0.78 cP Cp = 4.19 J/g °C
PROALEM # 22.a. mass at a pressure = 2at m and flow rate = 1020 kg /min, the temperature decreased from of hot water is being 248.09 °F to 212.09 oF using a heat exchanger. Reservoir water U used as w coolant with mass flow rate = 1800 ka lmin and inlet temperature = 50. 09 oF. The minimum = 270. 17 ft" of heat ex changer 2. allow able surface are a %3D all ow able overall heat = 206.05 btu/ %3D The transfer coefficient of heat exchanger maxi mum 2. The heat Capaci ty to be use d the average valme of must be inlet and outlet temperatures. Find the Number of Transfer units effective ness (NTU) usina if the heat NTU metho d exch anger being used is pipe heal exchanger counter-flow double
he shell fluid,ethylene glycol, enters at 120oC and leaves at 60oCwitha flow rate of 4000 kg/h. Water flows in the tubes, entering at 35oCand leaving at85oC. The overall heat-transfer coefficient for this arrangement is 900W/m2·oC.The exchanger is a shell tube with two shell passes and two tube passes.Calculate the following: a) The water exit temperature if flow rate of glycol to the exchanger is reduced in half with the entrance temperatures of both fluids remaining the same and by how much is the heat-transfer rate reduced?; b) The percentage reduction of heat transfer if water-flow rate is reduced by 25percent,while the gas flowrate is maintained constant along with the fluid inlet temperatures. Assume that the overall heat-transfer coefficient remains the same; andc) The flow rate of water required andthe area of the heat exchanger;
i need the answer quickly
Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine Cmin and Cmax Find c, e, and NTU Determine heat transfer rate for the heat exchanger. Determine the outlet temperatures of both fluids.