A severe weathering clay brick was tested for absorption and saturation coefficient according to ASTM C67 procedure and produced the following data:dry mass of specimen = 2.186 kgsaturated mass after 24-hr submersion in cold water = 2.453 kgsaturated mass after 5-hr submersion in boiling water = 2.472 kgCalculate absorption by 24-hr submersion, absorption by 5-hr boiling, andsaturation coefficient. Does the brick satisfy the ASTM requirements?

Q: The following data were measured for the freeze–thaw test, AASHTO T 283. Three samples were…

A: Given that the diameter of samples is 6 in  Convert inches to mm D = 6 in.  =  150 mm

Q: To test the compressive strength of cement mortar, three 2” cubes were cast with three different…

A: Given: Length of mortar cubes = 2 in   Mix No. w/c Ratio Cube No. Maximum Load (lb) 1…

Q: When tested, a 15 cm cube concrete specimen showed lower compressive strength compared to a 10 cm…

A: Given, when tested, a 15 cm cube concrete specimen showed lower compressive strenght compared to a…

Q: Use the list below of design requirements/assumptions to come up with the concrete mix design: A…

A:

Q: (b) Aggregate is one of the main materials used in the production of concrete and its physical…

A: Both the qualities of fresh concrete and those of hardened concrete may be significantly influenced…

Q: y consider the following data for concrete with mild exposure, calculate the quantity of cemer…

A: Given:Volume of water=191.6 litreWater cement ratio=0.5

Q: 51. Describe the process for the multiple stress creep recovery (MSCR) test on asphalt binder.

A: The Multiple Stress Creep Recovery (MSCR) test is a procedure used to evaluate the high-temperature…

Q: Write any five difference between Ordinary Portland Cement and Pozzolana Portland Cement

A: Ordinary Portland Cement (OPC): A blend of limestone and raw materials, such as gypsum,…

Q: 7 The specific gravity and absorption test (ASTM C128) was performed on fine aggregate and the…

A:

Q: The following plot belongs to a concrete slab and is intended to determine the formwork removal…

A: Datum Temperature of concrete mix = -50 CFind the Formwork removal time.

Q: 5.8 A sample of wet aggregate weighed 297.2 N. After drying in an oven, this sample weighed 281.5 N.…

A:

Q: To estimate the strength of concrete in a structure very quickly. To monitor setting and hardening…

A: Nondestructive testing (NDT) refers to a collection of testing techniques used to evaluate the…

Q: What is the recommended volume of Portland cement that can be replaced by fly ash? OA) 40-50% O B)…

A: Find answers in below tab

Q: The nominal maximum size for an aggregate is the standard sieve opening immediately smaller than the…

A: Answer:-  Nominal maximum size of an aggregate:- The smallest sieve opening through which the entire…

Q: Q-5, In a concrete mix of proportion 1:3:6, find the actual quantity of sand, which is judged to…

A: Given- Concrete mix proportion- 1:3:6, Bulking =15 %, It is needed to find the actual volume of the…

Q: Determination of Normal Consistency of Hydraulic Cement Calculation Calculate the amount of water…

A:

Q: e properties of five different pozzolans: Ground blast furnace slag, Silica Fume, Class F fly ash,…

A: Pozzolans, a large class of siliceous and aluminous minerals, are chemically reactive with calcium…

Q: 50- Vibration compasted Hand compacted Compressive Strength (28 days) MPa 15 0.6 Waterlcement Ratio…

A:

Q: A mix design for a major sidewalk construction  project is required. The concrete will not be…

A: To determine the mix design amounts for the concrete, we need to calculate the proportions of the…

Q: A sample of coarse aggregate was tested in a laboratory to find its moisture content. The wet weight…

A: Dry weight=5235.1gmWet weight=5403.5gmMoisture content=Wwet-WdryWdry×100Free water=MC-Absorption

Q: nstruction: Please provide complete solutions and box final answers.

A: S.no  Strength in Mpa  Mean  (X-mean) (x-mean)^2         1 38.3 41.735 -3.435 11.799225   3.074275…

Q: Aggregate is one of the main materials used in the production of concrete and its physical…

A: In concrete more than 70% volume is filled by aggregate hence if any problem in aggregate then it…

Q: Find the reading of the device for tensile testing of cement mortar in the unit KN if the cement…

A: given data from the question -  1. Tensile strength = 1.5MPa 2. A = (2 * 2.3)cm^2

Q: A concrete beam sample with a length of 21 inches has a square cross-section. The cross-sectional…

A:

Q: Membersof the ACI Building Code committee conducted a study, and the results showed that the scatter…

A:

Q: TRUE OR FALSE The recommended air content decreases with increasing the nominal maximum aggregate…

A:

Q: Review and explain the influences on the workability and compressive strength of concrete where the…

A:

Q: the soundness test a specimen of hardened cement paste isfor a fixed time. a) Freeze p) Dry C)…

A: Soundness test is used to check the concrete does not show much change in volume after setting . In…

Q: Design the concrete mix according to the following conditions: het Design Environment Pavement slab,…

A: Given, Design strength (f'c) = 5000 psi  Admixture dose = 0.15 fl oz/1% air/100 lb

Q: High Soundness value for the aggregate testing provide better resistance can to disintegration. True…

A: True.

Q: The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following…

A:

Q: quantity of (cement, fine aggregate, coarse aggregate and water) for 1m³

A: Solution: Choice of slump = 45 mm Choice of maximum size of aggregate = 28 mm Estimate of water…

Q: Coarse aggregate is not part of standard mortar mixture True O False

A: Mortar is a combination of a binding material and a supporting material. The binding material could…

Q: Calculate the average density of brick. ?

A: Brick No. Length mm Width mm Depth mm Mass kg 1 213 98 70 2.52 2 212 98 70 2.5 3 211…

Q: ): In a laboratory examination on a model of bricks, it was found that: 1. Moisture content 10% 2.…

A: Given data in question  Moisture content 10% Saturation degree 39% Apparent specific gravity 1.83 To…

Q: -if the volume of open pores of clay brick is 760 cm3, and its saturated weight equal to 5000 gm ,…

A:

Q: Concrete is required for walls of a building that will be Mild Exposed to freezing and thawing. The…

A: Solution: Given: Compressive strength = 35 MPa Slump = 55 mm Cement: Type = 1 Specific gravity =…

Q: A concrete masonry unit was tested according to ASTM C140 procedure and produced the following…

A: Solution:-

Q: Calculate the chemical shrinkage (cm3/g) for one gram of completely hydrated Portland cement with…

A: Given, C3S = 65% C2S = 19% C3A = 4% C4AF = 9%

Q: The estimated quantity of coarse aggregate (gravel) in (m3) of the floor concrete (1:2:4) that has…

A: To Determine Quantity of coarse aggregate (gravel) in (m3) of the floor concrete (1:2:4) that has…