Some testing on fire clay brick was performed such as density, water absorption andcompression test. The result obtained has shown in Table Q2.So Calculate the average density of brick. ? TABLE Q2WaterCompressionBrick sizeabsorption testBricktestWidthDepth(mm)Maximum forcelength(mm)no.MassMassMass(mm)(kg)dry (kg) wet (kg)(kN)121398702.522.52.82313221298702.52.482.8323321197692.482.472.77357

Brick No. Length mm Width mm Depth mm Mass kg 1 213 98 70 2.52 2 212 98 70 2.5 3 211…

Answered: Calculate the average density of brick.…

Engineering

Civil Engineering

Calculate the average density of brick. ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: To test the compressive strength of cement mortar, three 2” cubes were cast with three different…

A: Given: Length of mortar cubes = 2 in Mix No. w/c Ratio Cube No. Maximum Load (lb) 1…

Q: .: using the British Method, design a Concrete mix for a blinding with a specified characteristic…

Q: When tested, a 15 cm cube concrete specimen showed lower compressive strength compared to a 10 cm…

A: Given, when tested, a 15 cm cube concrete specimen showed lower compressive strenght compared to a…

Q: adhesion between cement and aggregate paste more important in highly resistant concrete 5- Why is it…

A: 1.) Temperature changes could cause cracks or sapling, distress, and aggregate expansion which leads…

Q: ilure of a reinforced concrete beam is 78kN. The dimensions of the beam are 100 mm x 100 mm x 1000…

A: Given:- total load=78kN The dimensions of the beam=100 mm x 100 mm x 1000 mm Water-cement ratio=0.5…

Q: Use the list below of design requirements/assumptions to come up with the concrete mix design: A…

Q: Compute for the DESIGN MIX of concrete a. by volume b. mass basis c. in situ state I. II.…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Calculate the quantities of cement, water, and fine aggregate and coarse aggregate per trial mix of…

A: Target mean strength= 50+1.65*5= 58.25 MPa w/c ratio =0.5 Slump value = 30-60 mm maximum size of…

Q: y consider the following data for concrete with mild exposure, calculate the quantity of cemer…

A: Given:Volume of water=191.6 litreWater cement ratio=0.5

Q: Three 100*200 mm cylindrical concrete specimens were tested for 28 days compressive strength and…

A: Solution: Given: Three Compress strengths of same concrete sample: C1=25.5MPa C2=28.6Mpa C3=24.8MPa…

Q: 7 The specific gravity and absorption test (ASTM C128) was performed on fine aggregate and the…

Q: The volume of gravel and cement used in a 1 ft3 concrete mixture is 0.58 ft3 and 0.12 ft3,…

A: Given, Vgravel = 0.58 ft3 Vcement = 0.12 ft3 Vconcrete = 1 ft3

Q: Calculate the quantities of cement, water, and fine aggregate and coarse aggregate per trial mix of…

A: building material : The term "building material" refers to construction materials. Many naturally…

Q: The specified 28-day compressive strength of concrete for a project is fc’ = 36MPa. This statistical…

Q: is the required average compressive strength to be used in your mix design? a. 3900 psi; b) 4000…

A: Concrete and rcc:

Q: 1. (a) The data presented below is compiled to obtain the modulus of rupture values of the MgO…

Q: The characteristic compressive strength of concrete required in a project is 25 MPa and the standard…

A: Given- fck=25 MPa,standard deviation σ=4 MPa, It is needed to find the water cement ratio.

Q: What is the recommended volume of Portland cement that can be replaced by fly ash? OA) 40-50% O B)…

A: Find answers in below tab

Q: Adjustment of water content: From durability consideration, maximum water/cement ratio of a concrete…

A: Given data, Maximum water/cement ratio = 0.4 Minimum cement content = 450 kg/m3 Minimum slump = 150…

Q: The following table represents a concrete mixture that has not been completely proportioned. The…

A: Question is based on the concrete mixture (oven dry basis) . Proportion of water, Air, coarse…

Q: Propose suitable Methods of finding Workability of Dry, Normal and Self Compacting Concrete

A: Workability of dry compacting concrete can be found by compaction factor test.

Q: Calculate the weight of cement that should be in a batch if the design mix requires concrete to have…

A: The given data is shown below: Water-cement ratio=0.45Dry gravel=1258 kg/m3Water=122 kg/m3Air…

Q: What is the amount of cement in kilograms needed for the design mix? (use two decimal places, no…

A: Answer To calculate the amount of cement in kilogram needed for the design mix we need to obtain…

Q: nstruction: Please provide complete solutions and box final answers.

A: S.no Strength in Mpa Mean (X-mean) (x-mean)^2 1 38.3 41.735 -3.435 11.799225 3.074275…

Q: m nominal maximum size, river gravel (rounded) Bulk oven-dry specific gravity = 2.55, Absorption =…

A: Calculate the corrected standard deviation as follows s'=F×s Here F is the modification and s is the…

Q: In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix…

Q: TRUE OR FALSE The recommended air content decreases with increasing the nominal maximum aggregate…

Q: We require a mix with a mean 28-day compressive strength of 40 MPa the size of the member and the…

A: Reference : ACI 318 Mix design All tables are taken from ACI 318 mix design. We are not allowed to…

Q: Mixing and handling can significantly alter the air content of fresh concrete. Thus, field tests are…

A: Air entrapped concrete is used generally in areas with low temperatures and damages can occur due to…

Q: Using the following data for n unreinforced Portland Cement Concrete pool deck: Design strength f'c=…

A: (a) The formula to calculate the compressive strength is given by, fm=fc+1.65σ ...1…

Q: water-cement ratio needed for the design mix?

A: As per ACI design mix procedure In air entrained concrete for the strength of concrete 5000psi,…

Q: Design the concrete mix according to the following conditions: het Design Environment Pavement slab,…

A: Given, Design strength (f'c) = 5000 psi Admixture dose = 0.15 fl oz/1% air/100 lb

Q: When conducting a laboratory test on brick samples, the following results were obtained: 8…

A: According to the Iraq standard no.25, The grades of bricks can be classified into three grades. They…

Q: For the following concrete mix design 1:0.51:1.29:3.6 (P:W:S:G), how much of each individual…

A: We will solve this question in step no. 2

Q: The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following…

Q: 5. Design the concrete mix according to the following conditions: Design Environment Building frame…

A: Concrete mix design includes a course of readiness wherein a blend of fixings makes the necessary…

Q: 12 Ibs of cement was mixed water to get 17 Ibs of cement-water mixture. What is the water-cement…

A: Given, In a mixture Amount of cement = 12 lbs Cement water mixture = 17 lbs we have to find water…

Concept explainers

Masonry Units

Concrete masonry is among the most surplus building materials present since a wide range of aspects can be accomplished using Concrete Masonry Units (CMU) as they have more benefits than stone or brick masonry. CMU are manufactured in a variety of shapes, colors, sizes, and patterns for various functions and finishing. Due to their modular properties, different CMU can be mixed in the same wall for various textures, colors, and so on. For the formation of the concrete blocks, cement, aggregate, and water are required.

Question

Some testing on fire clay brick was performed such as density, water absorption and
compression test. The result obtained has shown in Table Q2.

So Calculate the average density of brick. ?

TABLE Q2
Water
Compression
Brick size
absorption test
Brick
test
Width
Depth
(mm)
Maximum force
length
(mm)
no.
Mass
Mass
Mass
(mm)
(kg)
dry (kg) wet (kg)
(kN)
1
213
98
70
2.52
2.5
2.82
313
2
212
98
70
2.5
2.48
2.8
323
3
211
97
69
2.48
2.47
2.77
357

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data:

VIEW

Calculate the average density of brick:

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Give any two examples of samples of different types of aggregates and note the different shapes,textures and sizes. Discuss how each type might affect the concrete mixture.
1. Following data are given for designing a Portland cement concrete mix for a nonstructural sidewalk slab: • Design strength f´c= 26 MPa• Standard deviation of f´c obtained from 25 tests=1.4 MPa• Freezing and thawing and exposed to chlorides• Use air entrained concrete• Slab thickness= 300 mm• Fineness modulus of fine aggregate=2.7• Maximum aggregate size=50 mm and nominal maximum aggregate size=37.5mm• Bulk oven-dry specific gravity of coarse aggregate=2.6• Oven-dry rodded density of coarse aggregate=2002 kg/m3• Type I cement, relative density=3.1 Find the following:a) Required compressive strength b) w/c ratio c) Coarse aggregate amount (kg/m3) d) If the w/c ratio is 10% reduced, will the quantity of coarse aggregate increase, decrease or remain the same? Explain your answer.
The following table represents a concrete mixture that has not been completely proportioned. The values given are the theoretical mixture proportions (oven dry basis). Material properties are also provided. Please answer the question at the end of the information given. Theoretical Mixture Proportions (oven dry basis) 265 lb/yd3 675 lb/yd3 Water Cement Air |6.00 % Coarse Aggregate 1816 Ib/yd3 ASTM C 150 Type I Cement: Specific Gravity: 3.15 Coarse Aggregate: Well-graded 3/4 in. NMSA rounded gravel Oven-dry specific gravity: 2.63 Absorption: 1.10% Moisture content of stockpile: 3.10 % Oven-dry bulk density: 101.5 lb/ft³ Fine Aggregate: Natural Sand Oven-dry specific gravity: 2.60 Absorption: 3.20% Moisture content of fine stockpile: 3.50 % Fineness Modulus: 2.80 What is the water to cement ratio (w/cm) for this mixture? Round to two decimal places.
please quickly thanks !!
A severe weathering clay brick was tested for absorption and saturation coefficient according to ASTM C67 procedure and produced the following data:dry mass of specimen = 2.186 kgsaturated mass after 24-hr submersion in cold water = 2.453 kgsaturated mass after 5-hr submersion in boiling water = 2.472 kgCalculate absorption by 24-hr submersion, absorption by 5-hr boiling, andsaturation coefficient. Does the brick satisfy the ASTM requirements?
Compute for the corrected amount of water needed in the concrete mix if the mass of fine and coarse aggregates are 740 kg and 1100 kg, and both have a natural moisture content of 2% and 1.5% respectively. Water/cement ratio is 0.50 and the mass ratio of concrete is 1:2:3 o 216.3 kg o 171.9 kg o 170.2 kg o 153.7 kg Next.
The compressive strengths of a concrete sample at dry, air-dry and water saturated conditions are 24.5MPa, 22.6MPa and 21.5MPa, respectively. What's the softening coefficient of this concrete? () A) 0.92 B) 0.96 C) 0.13 D) 0.88
ASAP. Please,
A materials engineer is working in a research project to evaluate the effect of one type of admixture on the compressive strength of concrete. He tested eight mortar cubes made with admixture and eight others without admixture after 28 days of curing. The compressive strengths of cubes in MPa with and without admixture are shown in Table P6.38. Using the statistical t-test, is there a significant difference between the means of the compressive strengths of the two cement mortars at a level of signifi- cance of 0.10?
Asap pls
The characteristic compressive strength of concrete required is a project is 25 MPa and standard deviation in the observed compressive strength expected at site is 4 MPa. The average compressive strength of cubes tested at different water-cement (w/c) ratios using the same material as is used for the project is given in the table. Water content (%) 45 50 55 60 Average compressive strength of cubes (MPa) 35 25 20 15 20 15 The water-cement ratio (in percent, round off to the lower integer) to be used in the mix is
Create a design mix using the ACI DESIGN MIX PROCEDURE with the following parameters: Non-air Entrained Concrete Required Strength = 35 MPa Required Slump = 6 inches Maximum Size of CA = 3/4 inches Fineness Modulus of CA = 2.45 Density of CA = 1555 Kg/m3 SG of Water = 1.00 SG of Cement = 3.15 SG of CA = 2.84 SG of FA = 2.40