A second order system has the uinty feedback and open loop TF 20 G(s) : S(S + 10) a) Find Damping ration and natural frequency values, 0, Wd,tr,tp,ts, Mp, Peak time for the system output when excited by unit step input ? b) Sketch the transient response for unit step input ? c) If input is ramp of 0.565 rad/sec calculate steady state error?

A second order system has the uinty feedback and open loop TF 20 G(s) : S(S + 10) a) Find Damping ration and natural frequency values, 0, Wd,tr,tp,ts, Mp, Peak time for the system output when excited by unit step input ? b) Sketch the transient response for unit step input ? c) If input is ramp of 0.565 rad/sec calculate steady state error?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the figure, there is an ideal opamp connected to a resistor set from the non-inverting input in the circuit. The resistor set on the left feeds the circuit with different voltages while the switches below touch the resistors RA, RB, RC of different values. a.) If we call the input voltage Vi from the left resistor set, derive the expression that gives the Opamp's Gain. b.) Assume a fixed 10V output is read at the output of the circuit. In this case, if the current (I) is 100mA, 10mA and 1mA while the resistors A, B and C are installed, calculate the values of these resistors RA, RB and RC.
2) The amplifier circuit shown below has the following parameters: Rid = 200k, ro = 2k2, an open loop gain = μ = 106. If the factor 1+Aßf) = 15. a) State the type of feedback topology circuit. b) Identify the feedback portion of the circuit. c) Determine R₁1 and R22. d) Draw the small AC equivalent circuit of the below amplifier. e) Determine Aƒ. f) Determine Rif and Rof. Is S RS www +1₁ 100 R1 •MW". 3k OPAMP R2 ww 1k R3 R4 www 4k 3k Vo
BelowIn the unit feedback system given the shape, G(s),is given as. When a unit ramp is applied to the input of the system, 2% of the steady-state error and unit to the inputWhen the step is applied, it is desired that the percentage exceedance rate is 9.25% and the settling time is 0.58 s.1-In this case, which of the following is the approximate value of the constant a?
i need the answer quickly
5000 For the unity feedback system as shown below where G(s) %3D s(s+75) R(s) E(s) C(s) G(s) a. What is the expected percent overshoot for a unit step input? b. What is the settling time for a unit step input? c. What is the steady-state error for an input of 5u(t)? d. What is the steady-state error for an input of 5tu(t)? e. What is the steady-state error for an input of 5t²u(t)?
Please provide Handwritten answer
Consider a unity feedback system with the following open loop transfer function: G(s) = 5.7/[s(s+ 4) (s+20)] Using the second Ziegler-Nichols method design the PID controller G₂ (s) = K₂ (1+-+T₂5) The critical gain Kis a. 202.11 O b. 134.74 O c. 269.47 O d. 404.21 O e. 336.84
Consider an amplifier of this output-input characteristics: Vo = C₁ V₁ + C₂ V2 + ...... Assume these inputs: fA(t) = a cos wдt fB(t) = b cos WBt Also assume: C₁ = 0 Cn for n > 3 Find the following: a. The level of the 2nd & 3rd harmonics relative to the fundamental if only one input is used. b. Repeat if the sum of two inputs is used. c. Repeat if the difference of two inputs is used. For b & c the amplitudes of both inputs are the same.
I need the answer as soon as possible
BelowIn the unit feedback system given the shape, G(s),is given as. When a unit ramp is applied to the input of the system, 2% of the steady-state error and unit to the inputWhen the step is applied, it is desired that the percentage exceedance rate is 9.25% and the settling time is 0.58 s.1-In this case, which of the following is the approximate value of the constant a? 2-In this case, which of the following is the approximate value of the constant b? 3-Looking at the unit step response of the systemWhat is .peak time?
17. For the unity feedback system of Figure P9.1, with G(s) = K (s²+20s101) (s +20) the damping ratio for the dominant poles is to be 0.4, and the settling time is to be 0.5 second. [Sec- tion: 9.3] a. Find the coordinates of the dominant poles. b. Find the location of the compensator zero if the compensator pole is at -15. c. Find the required system gain. d. Compare the performance of the uncompensated and compensated systems. e. Use MATLAB or any other computer program to simulate the system to check your design. Redesign if necessary. MATLAB ML
When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.