2) The amplifier circuit shown below has the following parameters: Rid = 200k, ro= 2k2, an open loop gain = μ = 106. If the factor 1+Aßr) = 15. a) State the type of feedback topology circuit. b) Identify the feedback portion of the circuit. c) Determine R₁1 and R22. d) Draw the small AC equivalent circuit of the below amplifier. e) Determine Af. f) Determine Rif and Rof. Is RS www 1₁ 100 R1 •WW!! 3k OPAMP R2 ww 1k R3 R4 w 4k 3k Vo

2) The amplifier circuit shown below has the following parameters: Rid = 200k, ro= 2k2, an open loop gain = μ = 106. If the factor 1+Aßr) = 15. a) State the type of feedback topology circuit. b) Identify the feedback portion of the circuit. c) Determine R₁1 and R22. d) Draw the small AC equivalent circuit of the below amplifier. e) Determine Af. f) Determine Rif and Rof. Is RS www 1₁ 100 R1 •WW!! 3k OPAMP R2 ww 1k R3 R4 w 4k 3k Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Compared to circuit without feedback, the output impedance in current shunt circuit is A.unpredictable B.not related at all C.similar D.larger E.dependiing on frequency F.smaller
4. The circuit uses current- (or shunt-) feedback bias. The Si transistor has ICEO = 0, VCEsat =0, and B= 100. If RC = 2k and VCC =12V, size RF for ideal maximum symmetrical swing (that is, location of the quiescent point such that VCEQ =VCC/2). +V cc RC Cc Rs RL VL Cc R. R
6) Consider the following multistage amplifier. Draw the corresponding small signal model. Label, Vin, Vo1 and Vo. Do NOT make any approximations. Do NOT perform small signal analysis with this model. Just draw the small signal model. Show your work! Vin Vcc malli Q1 Re1 Vo1 Vcc ww1. Rc2 Q2 Re2 Vo
An inverting amplifier is to be designed with a gain of 5 and an input impedance of 10k ohms. What should be the value of the feedback resistance?
3) Explain the effect of input frequency increment on the output signal amplitude and phase (for circuit in figure 3). Make comments.
Answer the following with illustration and solutions. 2.) If C1 = C2 = 100pF, determine the output frequencies produced by this arrangement:a. (a) when R1 = R2 = 12kilo-ohms andb. (b) when R1 = R2 = 8kilo-ohms See the example below..
The amplifier configuration shown in figure below is a a) common emitter b) common collector c) common base d) base follower configuration, where the is at ac ground, and the ac output voltage a) collector B) emitter C) capacitor D) base with the input. A) amplified and 180deg out of phase B) almost equal and 180degree out of phase C) almost equal and in phase D) amplified and in phase
Find the desired values below in the feedback amplifier circuit in the figure. a) Voltage and current in amplifier circuit when Rf resistor is open circuit and RL resistor is present Show step-by-step the formula that gives the profit. b) Step of the formula showing the feedback current gain Ai when the Rf feedback resistor is connected find step.
The circuit uses current- (or shunt-) feedback bias. The Si transistor has ICEO = 0, VCEsat =0, and B= 100. If RC = 2k and VCC =12V, size RF for ideal maximum symmetrical swing (that is, location of the quiescent point such that VCEQ =VCC/2). +Vcc Rc Cc lic VL Cc R. -20 "ca. V -10 -12 14 -16
Consider the series-shunt feedback amplifier of Figure below. Assume that the voltage divider (R1, R2) is implemented with a 1-MN potentiometer. Assume that the MOSFET is %3D biased so that gm = 4 mA/V and r, is large. Also, Rp = 10 kN. VDD Find the value of R1 that results in a closed-loop gain of 5 V/V. Rp R2 R
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Vin?Vin = ____ volts
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Rin in ohms?Rin = ____ ohms