A screw jack mechanism is shown in the figure below (not drawn to scale). A belt drives a sheave that rotates the nut. The screw is a single-thread,1 1/2-4 ACME screw. Notice that a pin is used in a groove to prevent the screw from rotating. The sheave has a pitch diameter of 14 inches. The belt is driven by an electric motor (not shown) with a sheave pitch diameter of 2.8 inches at 1650 rpm. Determine the lifting speed of the jack. Determine the belt speed. Find the lifting speed (s) of the jack (in/min): Find the belt speed vb (ft/min):

Q: . Design a roller chain drive. Specify the chain size, the sizes and number of teeth in the nrockets…

A: given: kW=29.8          n1=500 rpm              n2=250 rpm For durability and noise consideration…

Q: A polyamide A-3 flat belt 6 in wide is used to transmit 15 hp under light shock con- ditions where…

A: Solution:-Given-Driving pulley Diameter d=30 in-Driving pulley rotation M=1774 rpm-Driven pulley…

Q: A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter…

A:

Q: The following figure depicts a 1600 rpm motor, gear box, and 4000 rpm blower. The gear box weighs 40…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 3. Calculate the torque and the rotation speed at the input pulley if the output pulley needs to…

A: (a) The torque at the input pulley is 66.67 lb•in. (b) The rotational speed of the input pulley is…

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

Q: 13-50 The figure shows a 10 diametral pitch 18-tooth 20° straight bevel pinion driving a 30-tooth…

A: Given,The diametral pitch,= 10The number of tooth on the bevel pinion, z = 18 toothThe pressure…

Q: 03/ The manually - operated hoist shown in figure (13) is based on an epicyclic gear train. The sun…

A: Given: The number of teeth on annulus, Za = 90 The tangential force on handle = 25 x load lifted

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: 3 L X x 5 ام 1-Motor; 2,6-Coupling; 3-Reducer; 4-High speed gear pair; 5-Low speed gear pair;…

A:

Q: below. Determine: (1) the torque in shaft c-d to the nearest in-lb and (2) the angle of twist at…

A: To determine the torque in the shaft and the angle of twist at a pointgivenradius of gear b=radius…

Q: solve the solution with answers given

A: Final Answer:-a) Fc  = 7200lb (part a)b)Fc = 2800lb(part b)c)78.4 ft.IbExplanation:Step 1: Step 2:…

Q: The shaft shown in the following figure is 200 mm long between self-aligning bearings at "A" and…

A:

Q: The figure shows a 16T 20° straight bevel pinion driving a 32 T gear and the location of the bearing…

A: Given data ;Power = 2 HpSpeed (N) = 200 rev/minr=2 inch

Q: please very urgent solving all part with count the link on the graph

A: I'll analyze both mechanisms based on the questions asked: a) Determining mobility using Kutzbach…

Q: Find the angle of contact on the small pulley for a crossed belt drive with center distance of 73",…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.