A sand sample of 35 cm2 cross sectional area and 20 cm long was tested in a constanthead permeameter. Under a head of 60 cm, the discharge was 120 mL in 6 min. The dryweight of sand used for the test was 1120 g, and Gs= 2.68. Determine (a) the hydraulic conductivity in cm/sec, (b) the discharge velocity, and (c) the seepage velocity

A sand sample of 35 cm2 cross sectional area and 20 cm long was tested in a constanthead permeameter. Under a head of 60 cm, the discharge was 120 mL in 6 min. The dryweight of sand used for the test was 1120 g, and Gs= 2.68. Determine (a) the hydraulic conductivity in cm/sec, (b) the discharge velocity, and (c) the seepage velocity

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A fine sand was tested in situ to give a coefficient of permeability of 3.7 x107 m/s. A sample of the same sand, 400mm high and 100 mm in diameter was then tested in a constant head permeameter. Water percolated through the soil under a head of 600mm for 5 minutes and the discharge water had a volume of 1300mm. Determine whether the in situ testing was reflected by the laboratory results and If the below water retaining structure is 140m in width, based on a coefficient of permeability of 7.8x10°m/s, determine the quantity of water that will flow through the soil and under the structure per day.
answwer in complete pls
The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 20 and the in situ moisture content is 45%. Determine the plasticity index. a.22 b.17 c.27 d.12
when a sample of medium sand was tested in a constant head permeameter, if the cross-section area of sample is 100 cm², hydraulic gradient is 10 and discharge collected is 10 cc/sec. Find the coefficient of permeability of the sand.
Q- Constant head permeability tests were performed on two soil specimens. S1 and S2. The ratio of height of the two specimens (LS1 : LS2) is 1.5, the ratio of the diameter of specimens (DS1: DS2) is 0.5, and the ratio of the constant head (hs1: hS2) applied on the specimens is 2.0. If the discharge from both the specimens is equal, the ratio of the permeability of the soil specimens (ksl: kS2) is.......
2. Estimate the hydraulic conductivity (in cm/sec) of a poorly graded sand with the following characteristics: d100 = 0.425mm, d50= 0.3mm, d30 = 0.25mm, d10= 0.2mm, and do = 0.1mm. Show your work and circle your answer.
Q- Constant head permeability tests were performed on two soil specimens. S1 and S2. The ratio of height of the two specimens (LS1 : LS2) is 1.5, the ratio of the diameter of specimens (DS1: DS2) is 0.5, and the ratio of the constant head (hs1: hS2) applied on the specimens is 2.0. If the discharge from both the specimens is equal, the ratio of the permeability of the soil specimens (ksl: kS2) is.......
In a constant head permeability test in the laboratory as shown in Figure Q2(e), the data is recorded in Table Q2(b). The void ratio of the soil specimen is 0.46. Determine; (i) Hydraulic conductivity, k, of the soil in cm/sec. (ii) Discharge velocity in cm/sec.
A cylindrical soil sample with length = 15cm and diameter = 4cm was taken from a site where a groundwater contamination piume was found. The sample was tested in the lab to determine its hydraulic conductivity. A hydraulic gradient of 0.05 was applied across the sample, and a flow rate of 0.025 cm³/sec was measured. Calculate the hydraulic conductivity of the soil sample using Darcy's law.
Problem (3) The hydraulic conductivity of a sand specimen at a void ratio of 0.55 is 0.051cm/sec. Estimate its hydraulic conductivity at a void ratio of 0.7.
For a falling-head permeability test, the following values are given:• Length of specimen 8 in.• Area of soil specimen 1.6 in.2• Area of standpipe 0.06 in.2• Head difference at time t 0 20 in.• Head difference at time t 180 sec 12 in.Determine the hydraulic conductivity of the soil in in./sec