The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 20 and the in situ moisture content is 45%. Determine the plasticity index. a.22 b.17 c.27 d.12

Q: Question 6.4 a) A core sample with a diameter of 1.2 in and a length of 1.8 in is saturated with…

A:

Q: 1) For a falling head permeability test, the following are given. Determine the hydraulic…

A: The falling head permeability test is performed to determine the hydraulic conductivity of a soil…

Q: A uniform weight of 20kN/m³ is distributed on large area. Estimate the consolidation settlement of…

A: Cs = 0.1 Cc = 0.24  = 20  kN/m3

Q: Estimate the teminal settling velocity in water at a temperature of 15 °C of spherical silicon…

A:

Q: Constant head permeability tests were performed on two soil specimens, S1 and S2. The ratio of…

A: given-soil specimen length ratios-Ls1Ls2=1.5Ds1Ds2=0.5hs1hs2=2

Q: In a triaxial test, total increament in cell pressure and total increament in deviator stress are…

A:

Q: Given that the clay layer drains on both its bottom and top sides as shown (a) Determine the…

A:

Q: nal solid solu

A: solution of above problem is below:

Q: Q'-4a

A: Given data -  Diameter of particles(d) = 0.10 mm  Rate of flow(Q) = 0.10 m³/s  gravity (g) = 9.81…

Q: The following are the result of shrinkage limit test. Vo (Saturated State) 25.4 cm3 Vf (Dry State)…

A: Given data -  Vo ( saturated state )  = 25.4 cm3 Vf (Dry State)  = 16.1 cm3 mo (Saturated State) =…

Q: A steel mesh of 0.3 m wide and 1.2 m long is placed within sand for a pullout test. The applied…

A: Calculate the pullout capacity of steel mesh in sand by using the relation

Q: The result of the liquid limit tests where N is the no of blows and w is the water content in % are…

A: optiona (a) is the correct answer

Q: A saturated N.C.C. with = 30 was tested in pressure of (200 kPa). Assume (Cau= C =0). a) Find the…

A:

Q: Example 5.2: - Formation water sample with solids concentrations of calcium (Ca) = 460 ppm, sulfate…

A: The values and figure given in the question are as follows: The concentration of Ca=460 ppm The…

Q: Water 3 m Clay 1 ki T+T2 n2 Clay 2 B. T2/2 k2 Sand Aquifer Shown in the image are two clay layers…

A:

Q: Choose the correct answer When the w/c = 0.42 and the degree of hydration is 50%, the volume of the…

A:

Q: Prove on your solution sheet that sg = (Se)/w or specific gravity is equal to the product of degree…

A: Question is based on the soil properties. In the question we have to prove the relation between…

Q: Determine void ratio Porosity=0.142

A: Given data : The value of porosity=n n=0.142   Required : Void ratio

Q: er. the Darcy velocity in the aquifer is 0.025 f/da- tio is 0.334. the longitudinal dispersion…

A: given data  contaminant mass of an aquifer =10 kg  velocity =0.1 ft/day  DL =0.01 ft2/day Dy =Dz…

Q: Estimate particle size of ilmenite (sg 2x sand =5.4) and anthracite (s.g. 2/3 of sand = 1.8) which…

A: Given data:Specific gravity of ilmenite = 5.4 Specific gravity of anthracite = 1.8 Specific gravity…

Q: Problem A mold having a volume of 0.12ft was filled with moist soil. The weight of the soil in the…

A:

Q: A course sand sample is placed in the constant permeameter test. What is the coefficient of…

A: Using Darcy law  Q=kia

Q: Summary of Answer: Suction Hydraulic Head 1 Head 42 Conductivi Difference ty (K) Suction Head Total…

A: Consider the given data z1=0.8=-80 cmz2=1.9=-190 cmz1-z2=-80+190=110 cm Total head, h=ψ+2z=gravity…

Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11 mm…

A: Find sorting coeffficient

Q: Constant head permeability tests were performed height of the two specimens (Ls1: Ls2) is 1.5, the…

A:

Q: Determine maximum principal stress

A: Given data : Normal stress in X direction σX=-11500 psi Normal stress in Y direction σY=-18250 psi…

Q: 12 cm, and the outside diameter of the well screen is 20 cm. Analyze this test and give the best…

A: Given data screen is 2 m long, inside diameter of the casing is 12 cm, and outside diameter of the…

Q: The result of the liquid limit tests where N is the no of blows and w is the water content in % are…

A:

Q: In the soil triaxial compression test, the test body is first compacted under a confining pressure…

A:

Q: 1. (e) One of the limitations of extending axis translation technique for measuring negative pore…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Water flows through a sand filter as shown on the figure. The soil has a cross sectional area of…

A:

Q: Calculate the permeability coefficient(mm/sec) for silty sample of area 7000 cm2, length 150mm. the…

A:

Q: Determine the liquid limit. Determine the plasticity index. Determine the liquidity index.

A:

Q: + wide plange w/ the pollowing properties A shown below is to be used as a column with an effective…

A:

Q: A fine sand was tested in situ to give a coefficient of permeability of 3.7 x107 m/s. A sample of…

A: The objective of the question is to determine whether the in situ testing was reflected by the…

Q: b. Consider the downward flow of water through a layer of sand in a tank shown below. For the sand,…

A:

Q: Degree of saturation is the ratio of volume of water in the voids to the *.volume of the voids True…

A: Based on the 3 phase diagram of soil We have Total volume of soil (V) is equal to sum of Volume of…

Q: Define Mohr–Coulomb Failure Criterion

A: The Mohr–Coulomb  failure criterion is a set of linear equations in principal stress space…

Q: From the given figure: Tank 10mY = 8kN/m oil G.S. 4m SAND 6m CLAY Determine the loss in pore water…

A: Degree of consolidation = 30 %   or 0.30  external pressure increase = γoil ×h = 8×10 = 80 KN/m2

Q: Q7- For the soil profile and loading condition shown in figure. The final settlement of the clay…

A: Given data:  unit weight of sand, γt=17 kNm3, γsat=20 kNm3 Unit weight of clay, γsat=21 kNm3…

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.