A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1 and R2. The shaft is loaded with a transverse load of 13 kN as shown in the figure. The shaft is made from AISI 1045 hot-rolled steel. The surface has been machined. Determine a) The minimum static factor of safety based on yielding b) the endurance limit adjusted as necessary with Marin factors  c) the minimum fatigue factor of safety based on achieving infinite life

Q: A solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of…

A:

Q: Problem 8-53: The coiled spring is subjected to a force P. If we assume the shear stress caused by…

A: Given Data:A coiled spring is subjected to a force P.The shear stress caused by this force on any…

Q: Link 2, shown in the figure, is 25 mm wide and 11 mm thick. It is made from low-carbon steel with…

A: Wide W = 25 mm Thickness t = 11 mm Sy = 165 MPaForce F = 80 KNFor  low-carbon steel E = 207GPa

Q: In the figure below the shaft is simply supported in ball bearings at A and D. The shaft rotates and…

A:

Q: 5-63 The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The…

A: The yield strength of AISI 1035 CD steel is 67 kpsi. Calculate the torque at pulley C. Calculate…

Q: pls find box ur answer Determine the value of the von Mises stress at point A. The von Mises stress…

A: The values are P=4 kN, F=0.55 kN, T=25 Nm The yield stress is Sy=280 MPa The length of the pipe is…

Q: Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

A: Given data: ● The load applied on the beam: W = 13 kN ● The diameter of the beam: d = 25 mm ● The…

Q: 6-10 A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R, and R2.…

A: Dear student please rate me positive :) Stay safe stay happy ! For AISI 1045 HRSut = 570MPa   , Syt…

Q: Required information A steel tube with a circular cross section has an outside diameter of 310 mm…

A: Steel tube with a circular cross section outside diameter D= 310 mm t= 2mm.  length, L=  2 m torque,…

Q: Fatigue and Variable Loading Example 4 In the figure below the shaft is simply supported in ball…

A:

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1 and R2. The…

A: Step 1: Step 2: Step 3: Step 4:

Q: Figure 1 is a schematic drawing of a countershaft that supports two V-belt pulleys. For each pulley,…

A: Given data, For pulley A Tension in tight side, T1 = 103 N Tension in loose side, T2 = 0.15T1…

Q: The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces…

A: Given:- Shaft is made up of AISI 1035 CD steel Speed of shaft = 1000 rpm  To Find:-  Minimum…

Q: 1) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is…

A: Treat the shaft as simply supported beam with supports at A and D.Here  are reaction forces at…

Q: Determine the endurance limit for this material as well as the value after correction for surface…

A: Given Data: AISI 1020 CD steelF=8 kNσe=235 MPa   To Find: The endurance limit after correction.

Q: Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: factor of safet

A: d= 40mmF = 29KNL = 796mmT = 1.7KNmfail stress = 156MPamaterial- brittle cast iron

Q: Required information This problem illustrates that the factor of safety for a machine element…

A: F = 0.55 kNP = 4 kN or 4000 NT = 25 N.mSy = 280 MPaLength of the bar, L = 100 mmDiameter of the bar,…

Q: The figure shows a schematic drawing of a vehicular jack that is to be designed to support a maximum…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.