6-10 A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R, and R2. The shaft is loaded with a transverse load of 13 kN as shown in the figure. The shaft is made from AISI 1045 hot-rolled steel. The surface has been machined. Determine (a) the minimum static factor of safety based on yielding. (b) the endurance limit, adjusted as necessary with Marin factors. (c) the minimum fatigue factor of safety based on achieving infinite life. (d) If the fatigue factor of safety is less than 1 (hint: it should be for this problem), then estimate the life of the part in number of rotations.

6-10 A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R, and R2. The shaft is loaded with a transverse load of 13 kN as shown in the figure. The shaft is made from AISI 1045 hot-rolled steel. The surface has been machined. Determine (a) the minimum static factor of safety based on yielding. (b) the endurance limit, adjusted as necessary with Marin factors. (c) the minimum fatigue factor of safety based on achieving infinite life. (d) If the fatigue factor of safety is less than 1 (hint: it should be for this problem), then estimate the life of the part in number of rotations.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and ultimate tensile strength of 700 MPa. Diameters of the shaft are D=30 mm and d=20 mm. Fillet radius of the shoulder section is 2.5 mm. The shaft is rotating and subjected to steady bending moment of M=51 Nm, steady torsion of T=58 Nm and steady axial load of F=14 kN. The operating temperature of the shaft is 20 ᵒC and reliability is 99%. The shaft has ground surface.Calculate the mean component of the shear stress (in MPa)
The solid steel rotating shaft in the figure is supported at B and C, and is driven by a gear, not seen, which is linked to spur gear D which has a pitch diameter of 150 mm. The drive gear force F acts at a pressure angle of 20 degrees. The shaft transmits a torque to point A of Ta-350 N.m. The properties of machined steel shaft are Sy-420 MPa and Sut-560MPa. Use a safety factor of 2.5 and determine the minimum allowable diameter in section B and C. Assume sharp felt radii at the bearing shoulders to estimate the stress concentration factors.Explain.
The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the gear on the shaft is 0.9 kg, dimension, surface and notch factors KbK / Kç = 0.83, shaft speed n = 1120 rpm, shaft transmitted power 7.5 kW, force on shaft Fn = F = 2680 N Since the desired safety coefficient is Ssafe = 2; Draw the bending and torsional moment diagrams of the shaft.
Please don't provide handwritten solution .....
Q8
(b) Figure 6(b) shows a cantilever shaft made of steel subjected to several loading T = 5kNm, M = 2.5kNm, and P = 120kN. If the diameter of the shaft is 60mm, and the yield stress is 310MPA, calculate the safety of factor of the shaft using the Von Mises yield criterion.
0.6- 0.3 1.0 4.2 320 lb 1:25- 5.25 340 lb 2 1.0 1.95 0.3 B 0.6
Urgent
A simply supported shaft is shown in figure below. A constant magnitude distributed unit load p=1000 Nicm is applied as the shaft rotates subject to a time-varying repeated torque that varies with maximum value of Tmar=2000 N.m. Find the diameter of shaft required to obtain a safety factor of 2 in fatigue loading if the shaft is steel of S =745 MPa and S, = 427 MPa. The dimensions (I= 20, b = 18 and a = 16) are in cm.
Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb clockwise to 1000 in-lb counterclockwise as an applied bending moment at a critical section varies from + 4000 in-lb to 2000 in-lb. The shaft is of uniform cross section and no keyway is present at the critical sec- tion. Determine the required shaft diameter. The material has an ultimate strength of 80,000 psi and a yield strength of 60,000 psi. Base design on a factor of safety N=1.5. Take the endurance limit as half the ultimate strength.
The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and ultimate tensile strength of 700 MPa. Diameters of the shaft are D=30 mm and d=20 mm. Fillet radius of the shoulder section is 2.5 mm. The shaft is rotating and subjected to steady bending moment of M=51 Nm, steady torsion of T=58 Nm and steady axial load of F=14 kN. The operating temperature of the shaft is 20 ᵒC and reliability is 99%. The shaft has ground surface. Calculate the alternating component of the normal stress (in MPa). (If there is no alternating component of the normal stress, enter "0" in the answer box)
Design